The large piston of a hydraulic lift had a cross-sectional area 10 times more than the small cross-sectional area. Determine the force F2 (Instruction: Type your answer without any unit. Type only the number)

The large piston of a hydraulic lift had a cross-sectional area 10 times more than the small cross-sectional area. Determine the force F2 (Instruction: Type your answer without any unit. Type only the number)

Name: The large piston of a hydraulic lift had a cross-sectional area 10 ti
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: The large piston of a hydraulic lift had a cross-sectional area 10 times more than the smallcross-sectional area. Determine the force F2(Instruction: Type your answer without any unit. Type only the number)F1 = 20 NSmall Piston, A1Large Piston, A2F2

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 6P: The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Similar questions

(a) Estimate the time it would take to fill a private swimming pool with a capacity of 80,000 L using a garden hose delivering 60 L/min. (b) How long would it take to fill if you could divert a moderate size river, flowing at 5000 m3/s, into it?
Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
How much pressure is transmitted in the hydraulic system considered in Example 11.6? Express your answer in pascals and in atmospheres.
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
(a) Convert normal blood pressure readings of 120 over 80 mm Hg to newtons per meter squared using be relationship for pressure due to the weight of a fluid (p=hg) rater a conversion factor. (b) Explain why be blood pressure of an infant would likely be smaller than that of an adult. Specifically, consider the smaller height to which blood mast be pumped.
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
(a) Using Bernoulli's equation, show that be measured fluid speed v for a pitot tube, like the one in figure 14.32(b), is given by v=( 2gh)1/h , where h is be height of be manometer fluid, p' is the density of the manometer fluid, p is the density of the moving fluid, and g is be acceleration due to gravity. (Note that v is indeed proportional to the square root of h, as stated in text) (b) Calculate v for moving air if a mercury manometer's h is 0.200 m. Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.
Gasoline is piped underground from refineries to major users. The flow rate is 3.00102m3/s (about 500 gal/min), viscosity of gasoline is 3.00102m3/s , and its density is 680 kg/m3. (a) What minimum diameter must be pipe have if the Reynolds number is to be less 2000? (b) What pressure difference must be along each kilometer of be pipe to maintain flow rate?
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.
What is density of a woman floats in fresh water with 4.00% of her volume above the surface? (This could be measured by placing her in a Wii marks on the side to measure how much water she displaces when floating and when held under water.) (b) What percent of her volume is above surface when she floats in seawater?
A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.