The magnitude of the line voltage at the terminals of a balanced Y- connected load is 12800 V. The load impedance is 216+j63 /p. The load is fed from a line that has an impedance of 0.25+j2 n/p. ▼ Part A What is the magnitude of the line current? Express your answer to four significant figures and include the appropriate units. IL = Submit Part B Vab= μA Submit Value Request Answer 3 What is the magnitude of the line voltage at the source? Express your answer to five significant figures and include the appropriate units. μA Value 1 Units Request Answer ? Units ?

The magnitude of the line voltage at the terminals of a balanced Y- connected load is 12800 V. The load impedance is 216+j63 /p. The load is fed from a line that has an impedance of 0.25+j2 n/p. ▼ Part A What is the magnitude of the line current? Express your answer to four significant figures and include the appropriate units. IL = Submit Part B Vab= μA Submit Value Request Answer 3 What is the magnitude of the line voltage at the source? Express your answer to five significant figures and include the appropriate units. μA Value 1 Units Request Answer ? Units ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
Q1. For the system shown in Figure Q1, draw an impedance diagram in per unit, by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators. 10 KVA 2400 V G₁ Z=j0.2pu 20 KVA 2400 V Z=j0.2pu G₂ T₁ Transmission Line Z= (50+j200) 40 KVA 2400/9600 V Z=j0.1pu Fig Q1 T₂ 80 KVA 10/5 kV Z=j0.1pu M 25 KVA 4 kV
For the bridge circuits shown in the figure bellow, derive expressions to calculate the unknown impedances. B Detector E B Detector Ry wwlle
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
estions:- 1. Identify unity power factor points on V-curves and comment why you will not get unity power factor at same It for vanous loads?
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I
A 3-phase delta connected load is supplied by a 11/0.4 kV, star-delta connected transformer. The load impedances are Z1 = 20 + j0 ohms, Z2 = 10 – j5 ohms and Z3 = 15 + j10 ohms. Determine the line currents and also currents in the secondary windings of the transformers
Using Figure 1, Vs 50V-15 339 Hz R1 $1100 R2 100 www XL1 320 HH XC1 Figure 1 700 R3 600 13 R4 400 XL2 1902 XL3 450 XC2 650 a. Determine the total circuit impedance, ZT. b. Calculate current IT. c. Calculate currents I, and I3. State the value of these currents in both rectangular and polar form. d. For each of the currents determined in part c, answer the following: Is the current leading, lagging, or in phase with the source voltage. e. Use the voltage-divider rule to determine the voltages across XL1 and Xc2.
The single-line diagram of a subtransmision system is presented in the figure below. At point B a three- phase short circuit has occurred. Calculate the voltage at points A, B, C and D. Three phase short circuit Infinite bus D +j0.2 j0.67 +10.70 +j1.05 V-1.00 pu
For the bridge circuits shown in the figure bellow, derive expressions to calculate the unknown impedances. R2 ww B Detector B Detector ww- welle