The outside temperature of a 10 ft² hot insulated pipe is 140 °F and the surrounding atmosphere is 60 °F. The heat loss by free convection and radiation is 13,020 Btu/hr·ft²·°F. How much of the heat loss is due to radiation? Assume the pipe emissivity is approximately 0.9

The outside temperature of a 10 ft² hot insulated pipe is 140 °F and the surrounding atmosphere is 60 °F. The heat loss by free convection and radiation is 13,020 Btu/hr·ft²·°F. How much of the heat loss is due to radiation? Assume the pipe emissivity is approximately 0.9

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.69P: The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per...

See similar textbooks

Related questions

Q: A 75-hp (shaft output) motor that has an efficiency of 91.0 percent is worn out and is replaced by a…

A: Given Data: The output power of the older shaft motor is (Wo)1= 75 hp The efficiency of the older…

Q: Which one of the following expresses the thermal diffusivity of a substance in terms of thermal…

A: Thermal diffusivity (α) is a measure of how quickly the heat can get dispersed in a material. It is…

Q: What are the mechanisms of heat transfer?

A: There are three mechanisms by which the heat transfer can take place. They are conduction,…

Q: Calculate the thermal resistance due to convection for the following situations:a. w arm water with…

A: Given Data: a. w arm water with h = 200 W⁄m2 .Kb. warm air with h = 10 W⁄m2 .Kc. warm moving air…

Q: The inverse square law of heat states that intensity of radiation is not inversely proportional to…

A: True

Q: 1 m² at 0 ⁰C and 1 atm pressure during a 244 hour operation at 8 m/s wind speed. Calculate the…

A: Given Data: The given area, A = 1 m2. The temperature, T = 0°C. The pressure, P = 1 atm. The…

Q: A Gasoline engine operating on an air standard condition has a clearance volume of 15cm3 and a…

Q: In thermodynamics, how do you differentiate a closed system with an adiabatic system? What is the…

A: 1. Closed system: A closed system is a thermodynamic system through which there is no mass transfer…

Q: 9. Calculate the specific work done by the environment on a spherical parcel of air at 105 Pa over a…

Q: What are the three modes of heat transfer? Describe each briefly.

A: There are three modes of heat transfer namely as follows; 1- Conduction, 2- Convection and 3-…

Q: The following unit conversions are illustrations of the SI system of units. Show cancellation of…

A: (a) Given: The thermal conductivity is 0.3 BTU/h ft oF. Calculation: one 0.3 BTU/h ft oF has…

Q: Does any of the energy of the sun reach the earth by conduction or convection?

A: Since there is no atmosphere in space between the Sun and the earth, the significant portion of the…

Q: Are the energy developed by heat, chemical reactions, and electromagnetic effects neglected in…

A: Basically mechanical engineering is broadly classified into three parts and they are thermal…

Q: 02. An electronic box that consumes 180 W of power is cooled by a fan blowing air into the box…

A: We are supposed to answer only 3 parts, please post remaining parts as a separate question.

Q: A 3 inch schedule 40 pipe is covered with two layers of…

A: Given data: 3 inch schedule-40 pipe means nominal diameter is 3 inch and it's outside diameter is,…

Q: Overall heat transfer coefficient for the combined mode of heat transfer "Convection Conduction…

A: Draw the diagram of the composite pipe of 2 layers.

Q: What are the equations for heat transfer from conductions, convection, and radiation?

A: The conduction heat transfer mainly occurs in solid to solid heat transfer and its equation is…

Q: Air at 300 degrees Celsius flows over a plate of dimension 0.5 m by 0.25 m. If the convection heat…

Q: How does the science of heat transfer differ from the science of thermodynamics? Give your answers…

A: Thermodynamics and Heat Transfer both are part of thermal engineering and each has its own meaning…

Q: The heat is dissipated from the plate by convection and radiation into surrounds at 20 C. Take ɛ…

A: Given Data

Q: A thermal efficiency of a cornbustion chamber valued equal to 73.15 % with heat supplied to the…

A: To find : determine the net work done produce . Given : thermal efficiency of a combustion chamber…

Q: 1. It is commonly recommended that hot foods be cooled first to room temperature by simply waiting a…

A: Given Data The mass of the pan is: m=5 kg The temperature of the kitchen is: T∞=20°C=293 K The…

Q: A 3-meter high room is heated through a vertical steam pipe. If the bulk temperature of steam in the…

A: Given data: *The height of the room is h=3 m. *The bulk temperature of the steam is Tb=25 degrees…

Q: There is a cylindical piece of nickel, that is 5 cm in diameter and 10 cm in length, that is…

Q: What four processes are involved in heat transfer?

A: Generally, there are 4 modes of heat transfer:- Conduction Convection Radiation Evaporation…

Q: A hot object suspended by a string is to be cooled by natural convection in fluids whose volume…

A: Solution: The correct answer to the question with the explanation is given below:

Q: 2.5-m-tall steel cylinder has a cross-sectional area of 1.5 m2. At the bottom, with a height of 0.5…

Q: Fins are used to improve heat transfer by increasing the effective * surface area TRUE O False O

A: Hi. as you have posted multiple questions and not specified which question needs to be solved, we…

Q: Determine the thermal boundary layer

A: Given data; A fluid prandi number,Pr=1 Temperature,T=500 KIt is flow over a plate, length,l=2.5…

Q: Heat transfer is a discipline of thermal engineering that concerns the generation, use, conversion,…

A: Thermodynamics is the branch of physical science that deals with the relations between heat and…

Q: The surface of a 0.5-m diameter space probe dissipates 150 W of heat to the outside. If the probe…

Q: Determine the specific heat of a 150.0 gram object that requires 62.0 cal of energy to raise its…

Q: Mercury at 25°C flows over a 3-m-long and 2-m-wide flat plate maintained at 75°C with a velocity of…

Q: Fluid in which shear stress is directly proportional to the rate of shear strain is O Ideal plastic…

A: A fluid, in which shear stress in directly proportional to the rate of shear strain or velocity…

Q: Define and briefly explain the terms listed below, support your elaboration with mathematical…

A: As per Bartleby's policy in the case of multiple subparts only the first 3 can be solved. Please…

Q: wo very large walls are at constant temperature of 658oF and 856oF. Assuming that the walls behave…

A: Given:T1=658°FT2=856°Fσ=0.1714*10-8 Btu/hr-ft2-R4

Q: A solid sphere 1 of radius 'r' is placed inside a hollow, closed hemispherical surface 2 of radius…

Q: Surface quality is affected due to Resistance strength of contact surfaces O Friction resistance of…

A: Given Surface quality To find Reason which affect surface quality

Q: Q2: Explain, motorcycle engine is either considered as free or forced convection. Justify your…

A: Heat transfer is carried out by three phenomenon 1) Conduction 2) Convection 3) radiation Convection…

Q: The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm.…

Q: SITUATION 3.1 Company AAA is going to construct a 8,000 square meters cold storage factory in 6…

Q: he convection heat transfer coefficient between a surface at 40°C and air at 20°C is 20 W⁄m2 − K.…

A: Given Heat transfer coefficient, h = 20 W⁄m2.K Initial Temperature, T1 = 40°C…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A box made of copper plate with outside dimensions of 5 ft by 5 ft by 6-in.is suspended horizontally in a large room where the air and wall temperaturesare 80°F. The box contains a heating coil which maintains a temperature of500 °F on all external surfaces. What is the total heat loss from the box inBtu/hr.
The temperature of a tank in the form of liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located .h = 4.35 W / m2K, e= 1.
Calculate the amount of energy required to heat the air in a house 30 by 50 by 40 feet from 10 to 70°F. The density of air is about 0.080 lbs/ft3, and its specific heat at constant pressure is about 0.24 BTU/lb-°F
Heat is lost through the glass pane of a window. The thickness of the glass is 3 mm, and the window is 0.9 m by 1.8 m. The thermal conductivity of glass is 0.8 W/mK. If the temperature difference across the glass is 17 K, what is the total heat transfer through the pane of glass? Give your answer in Watts to the nearest integer.
The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located: h = 4.35 W / m2K, ∈ = 1.
flat wall is exposed to the environment. The wall is covered with a layer of insulation 1.0 in. thick whose thermal conductivity is temperature of the wall on the inside of the insulation is 600°F. The wall loses heat to the environment by convection on the surface of the insulation. The 0.8 Btu/hr-ft-°F. The average value of the convection heat transfer coefficient the insulation surface is 950 on Btu/hr-ft-°F. Compute the bulk temperature of the environment (T) if the outer surface of the insulation does not exceed 105°F.
Required information Consider a person whose exposed surface area is 21 m4, emissivity is 0.5, and surface temperature is 32°C. Given: 0 = 5.67×10-8 W/m2.K4 Determine the rate of heat loss from that person by radiation in a large room having walls at a temperature of 300 K (upto 3 decimal places). You must provide an answer before moving to the next part. The rate of heat loss from the person at 300K is W.
The convection heat transfer coefficient between a surface at 40°C and air at 20°C is 20 W⁄m2 − K. Calculate the heat transfer per square meter leaving the surface.
The car is outdoors in direct sunlight. The outside air temperature is 27 ° C. The temperature inside the car is maintained by air conditioning 22 ° C. What is the temperature of the outside surface of the car roof? The power density of solar radiation is 840 W / m2 and the absorption coefficient of the roof paint for radiation is 0.51. The heat transfer coefficient from the roof surface to the outside air is 11.6 W / (m2K), which also includes heat radiation from the surface to the environment. Radiation from the atmosphere to the car is not taken into account. The total thermal resistance of the car's roof structure is 1.0 m2K / W. The task does not look at any other part of the vehicle but only the roof. If you need an area, make a calculation per 1 m2.
A large steel plate having a thickness of L = 4 in, thermal conductivity of k= 7.2 Btu/h·ft. °F, and an emissivity of ε = 0.7 is lying on the ground. The exposed surface of the plate at x = L is known to exchange heat by convection with the ambient air at T∞ = 90°F with an average heat transfer coefficient of h = 12 Btu/h·ft².°F as well as by radiation with the open sky with an equivalent sky temperature of Tsky =480 R. Also, the temperature of the upper surface of the plate is measured to be 80°F. Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the plate, (b) obtain a relation for the variation of temperature in the plate by solving the differential equation, and (c) determine the value of the lower surface temperature of the plate at x = 0. Tsky h, To Convection Radiation XA 80°F L E Plate 0 Ground
A 12-by-12 in. open pan containing water at 140 °F is placed in the exact center of a 16-by-20 ft room having a ceiling temperature of 75°F. If the distance from the water surface to the ceiling is 10 ft and the ceiling is painted with an oil paint, what is the net radiant-heat exchange between the water surface and the ceiling?
A flat wall is exposed to the environment. The wall is covered with a layer of insulation 1.0 inches thick whose thermal conductivity is 0.8 Btu/h*ft²*°F. The temperature of the wall on the inside of the insulation is 600°F. The wall loses heat to the environment by convection on the surface of the insulation. The average value of the convection heat transfer coefficient on the insulation surface is 950 Btu/h*ft²*°F. Compute the bulk temperature of the environment (Tb) if the outer surface of the insulation does not exceed 105°F.