The pinion (gear 2 on shaft a) rotates at 695 rev/min clockwise and transmits 1497 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 3 mm, and gears 4 and 5 have a module of 2 mm. Pressure angles are all 20 degrees.

The pinion (gear 2 on shaft a) rotates at 695 rev/min clockwise and transmits 1497 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 3 mm, and gears 4 and 5 have a module of 2 mm. Pressure angles are all 20 degrees.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical…

A: Given:To find:What is the number of blades used for the rough cutting steps?What is the number of…

Q: Total volume of the tanks m³ (two decimal accuracy) Final pressure of the mixture Molar fraction of…

Q: Derive a general expression to find circulation and the lift force for NACA 27014

Q: A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is under…

A: The distributed load is The length is The yield stress is The elastic modulus is The dimension of…

Q: The pelvis Pis connected to the femur Fat A using three different muscles, which exert the forces…

Q: What to Submit: Submit the following figures and table: • Temperature plot of steam pipe assembly in…

A: Given: THe The inner and outer diameter are The thermal conductivity of cast iron The temperature of…

Q: Help me!! Using the table below. Help me graph and find the graphing equation and step by step…

A: x-axis shows weight of the carsy-axis shows their mileage per gallon

Q: Problem 1-21: Determine the resultant internal loadings acting on the cross section at point E. The…

Q: Kerosene has an API gravity of 42.5. What is the specific gravity of kerosene at 16°C? How does this…

Q: 2.22 The two major forces opposing the motion of a vehicle moving on a level road are the rolling…

A: Given : The rolling resistance of tires is The weight of the car is The area of the car is The drag…

Q: 1.28 Vector concepts: Solving a vector equation? (Section 2.9.3) Shown right is a vector equation…

A: The objective of the question is to determine the validity of the process used to solve for the…

Q: his is a practice question, not graded assignment. Understand that to find the answer to below…

A: The thermal conductivity is The duct surface is heated uniformly.The distance of surface from the…

Q: The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure…

A: The objective of the question is to determine the location along the shaft where the shear stress is…

Q: PROBLEM 3 Mechanical system consists of solid body 1 of mass mm which is connected by non-clastic…

A: Given:The mass of the solid body 1, The mass of the disk 2, The radius of the disk The coefficient…

Q: 1. At what angle of attack (in deg.) must the airfoil be pitched to obtain zero lift? (answer…

A: Given:

Q: Air at 305 K flows at 4 m/s over a flat plate at 350 K. The air properties are as follows: density…

Q: Question 1 An industrial cold room has four 200 mm thick walls made of concrete. The walls are…

A: For the solution refer below images.

Q: A titanium alloy (Ti-5Al-2.5Sn) specimen with the dimensions shown below is subjected to a uniaxial…

A: The stress of a bar is given by, , where P is the normal load and A is the cross-section area of…

Q: 2-74. Determine the magnitude and coordinate direction angles of the resultant force, and sketch…

A: As per Bartleby's policy in case of multiple questions I can solve only first one.

Q: 1. A 0.75-m x 1.5-m window is constructe outside surface temperatures of the gla (a) What is the…

A: “Since you have posted multiple questions with multiple sub parts, we will provide the solution only…

Q: 1. Figure 1 shows a rocking mechanism that consists of two masses m₁ and m₂ connected by a rigid and…

A: For the solution refer below images.

Q: Gear A of the winch turns gear B, raising the hook H. Gear A starts from rest at t = 0 and its…

A: Given:Diameter of the gear ADiameter of the gear BTo determine:a)Upward velocity of the hook at…

Q: b) The von Mises equivalent stresses at point H can be calculated as MPa

A: For the solution refer below images.

Q: exhibit various physical behaviours. Sele scosity acts to diffuse the velocity field ontinuity…

A: The viscous effect is nothing but the force between the adjacent layer.

Q: A) A factory produces three types of products. Each of the products processing on two machines. The…

Q: Problem 2-5: The rectangular plate is subjected to the deformation shown by the dashed line.…

A: Given data:-The rectangular plate is subjected to deformationDetermine:-The average shear strain in…

Q: Problem: Three forces act on the ring. If the resultant force FR has a magnitude and direction as…

A: Three forces act on the ring. If the resultant force FR has a magnitude and direction as…

Q: In wire and cable coating with polymer, a slight vacuum is drawn between wire and polymer to promote…

A: The objective of the question is to understand the reason behind drawing a slight vacuum between the…

Q: Consider an ideal Brayton refrigeration cycle with a regenerative heat exchanger. Six kg/s of air…

Q: A beam is held by 2 steel rods, AB and CD. Three dead load forces are applied to the beam. The…

A: Find outDetermine the normal force in rod AB after accounting for the dead load factor,Determine the…

Q: Some engineers want a good estimate of drag and boundary-layerthickness at the trailing edge of a…

A: The objective of the question is to estimate the drag and boundary-layer thickness for the prototype…

Q: Steam enters the turbine of a vapor power plant at 600 lbf/in.2, 700°F and exits as a two-ph mixture…

A: To-Determine:-

Q: PROBLEM 3 3 Mechanical system consists of solid body 1 of mass mm which is connected by non-elastic…

Q: Problem # 01: If F₂ =30lb and Fc =45lb, determine the resultant moment about the bolt located at A…

Q: For the gear train below, the teeth numbers of the gears are N2= 47. N3-16, N4 = 30. N5-15. If the…

A: Given:The number of teeth on gear 2, The number of teeth on gear 3, The number of teeth on gear 4,…

Q: - What is the vapor pressure when a liquid that obeys the Trouton rule boils at a temperature equal…

A: Given:The liquid is boiling by 1/3 normal boiling temperature. According to the Trouton rule, at…

Q: Steam flow meters on an industriai process line recorded maximum flow rates of 57,900 lb per hr for…

A: from steam table Specific Volume at 40 psig=7.82 cuft/lb

Q: I’m a doing a stiffness compliance matrix. E_1 is 150 GPA; what are the units of E_1 when I do…

Q: Thermal efficiency of an ideal Otto-process: Select one: O a. depends from both compression ratio…

A: Given statements

Q: 1. The 25-kg box is launched from the position shown along the rough horizontal plane with the…

A: Spring is a flexible object that can store mechanical energy. The most common material used to…

Q: He- 36" -24" 王 40"

Q: An enterprise combines factors E & R to form an item for consumption which is must weigh at least…

A: Given:The weight of the item formed by combining factors E and R is at least The consumption of…

Q: How much work

A: N is normal reaction force between contacting surface.mg is weight force.F is pulling force.a is…

Q: I have the same question in my book. But the Rod is 30 kilogram and 1.5M length from A to B and…

Q: For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the…

A: The given beam with udl is shown in the figure.To find: To draw the shear and bending moment…

Q: Vp = A camera tracks the position of a particle moving along the given path with b = 10 m. At the…

A: The objective of the question is to find the radial and transverse components of velocity and…

Q: Problem 1-37: The plate has a width of 0.5 m. If the stress distribution at the support varies as…

A: Given:Width of the plate, Stress distribution on the support, Length of the plate,

Q: In the United States, energy for household heating is generally sold using English units, e.g.,…

A: Given:The efficiencies are based on the HHV. Assume the cost of natural gas is $8/MBtu, the cost of…

Q: Air at 20°C with a convection heat transfer coefficient of 25 W/m2 K blows over a horizontal steel…

A: Find outthe inside plate temperature isgiven dataAmbient temperature, Convection heat transfer…

Q: 32: find the resultant. 20 F₁ = 3N 4m 2 1m F₂=6N Lm 13 N.m

Concept explainers

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.

Question

The pinion (gear 2 on shaft a) rotates at 695 rev/min
clockwise and transmits 1497 W through the idler
pair (gears 3 and 4 on shaft b) to the output gear (gear
5 on shaft c). Gears 2 and 3 have a module of 3 mm,
and gears 4 and 5 have a module of 2 mm. Pressure
angles are all 20 degrees.
Solve for the magnitude of the force that shaft b must
apply to gears 3 and 4 to maintain static equilibrium in
the figure shown here.
Co
18T-
327
X
18T
5
-48T

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables-

VIEW

Step 2: Determine magnitude of force that shaft b must apply to gears 3 and 4 to maintain static equilibrium

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 20 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
The bevel gear train shown is called Humpage’s reduction gears. The input is to gear 2,and the output from gear 6, which is connected to the output shaft. The arm 3 turns freelyon the output shaft and carries the planets 4 and 5. Gear 7 is fixed to the frame. What isthe output speed if gear 2 rotates at 2,000 rpm?
Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output gear D through a compound gear BC. The number of teeth on the gear A, B, C and D are 16, 32, 12 and 18 respectively. Given: Module = 4mm, pressure angle=20° The tangential force acting on the gear B is N A D В
Q4:- Two shafts A and B in the same straight line are geared together through an intermediate parallel shaft C as shown in the Fig. below. The gears connecting A and C have a module of 2 mm, those connecting C and B have a module of 3.5 mm. The speed of B is to be about (0.1) that of A. If the two pinions have 24 teeth, find the most suitable number of teeth for the gears, the actual velocity ratio and the corresponding center distance. 2 3 4
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and transmits a torque of 20 N-m. The torque transmitted by the gear is
The power and motion can be transmitted from one shaft to another shaft by means of gear drives if center distance between the shafts is very large. Select one: True False
consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number of teeth on gear planeta (3) is Z3 = 20 and the number of gear anel (4) Z4 = 70 the speed of gear sol, w2 = 300 rpm and of anel w4 = 200 rpm find the speeds of gear sol and braço carregador b
An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth and sun gear has 32 external teeth . Planet gear meshes with both ring and sun gears and carried an arm which rotates about the centre of the ring gear at 20 r.p.m . If the gear A is fixed. Calculate the speed of planet gear.
The pitch circle diameter of the smaller of the two spur wheels which mesh externally and have involute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and the addendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.