The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.19-in.-diameter piston of the hydraulic-cylinder unit AB. Assume a = 6 in., b = 33 in., c = 18 in., e = 38 in., and 9 = 38° Answers: C = p= i i B 8 lb lb/in.²

The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.19-in.-diameter piston of the hydraulic-cylinder unit AB. Assume a = 6 in., b = 33 in., c = 18 in., e = 38 in., and 9 = 38° Answers: C = p= i i B 8 lb lb/in.²

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.129P: The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the...

See similar textbooks

Similar questions

The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the cable.
The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.46-in.-diameter piston of the hydraulic-cylinder unit AB. Assume a = 7 in., b = 34 in., c = 17 in., e = 36 in., and θ= 32°.
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 42 45 100 Ib 18 3 ft 3 ft- 30 200 Ib ft 30" 30 30 kg 2 ft B B Fig (1) Fig (2) Fig (3)
The portable floor crane in the automotive shop is lifting a 530-lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure p against the 3.36-in:diameter piston of the hydraulic-cylinder unit AB. Assume a- 5 in, b= 33 in, c= 14 in, e 54 in, and e = 36. Answers: Ib Ib/in? p=
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 45 100 Ib te-18 15 3 ft 3 ft- 30 200 lb ft 30 30 30 kg 2 ft B 12 Fig (1) Fig (2) Fig (3)
For the system shown (for the extension strokes of the cylinders), what pump pressure is required if the cylinder loads are 12000 lb each and cylinder 1 has a piston diameter of 6in?
Figure is a simplified sketch of the mecha- nism used to raise the bucket of a bulldozer. The bucket and its contents weigh 10 kN and have a center of gravity at H. Arm ABCD has a weight of 2 kN and a center of grav- ity at B; arm DEFG has a weight of 1 kN and a center of gravity at E. The weight of the hydraulic cylinders can be ignored. Calculate the force in the horizontal cylinders CJ and El and all forces acting on arm DEFG for the position shown. 30°1, 30° 0.6 m 0.9 m 0.6 m 0.9 m 0.6 m 0.9 m 0.3 m
2: This fuel pump uses the reciprocating action of rocker arm ABC. The arm is pinned at B and is spring loaded at A and D. Calculate the forces acting at pin B and in the spring at point D. Fc= 125 N FA = 60 N 20 mm- 10 mm 50 mm
Determine bar forces. Refer to the question in the image.
The pressure vessel shown below is being lifted by two cables that are attached to the bottom of the tank at points L = 6' away from each other. Assume that this causes reaction forces at the bottom of the tank that are oriented in the direction of the cable, i.e. 30 degrees from vertical. The tank weighs 4,970 lb. For simplicity, assume that the weight is evenly distributed from one connection point to the other, thus ignoring any weight in the end caps. Also assume that the tank is pressurized to 272 psi. The tank has an internal radius of 1.7 ft and a thickness of 1/8 inch. The tank is made out of steel with a 50 ksi yield strength. Determine 1) the combined stress state at point C, which is located at mid-length at the bottom of the tank and 2) the factor of safety against yielding at point C using the Tresca criterion. be sure to clearly indicate your answers to parts 1 and 2.
Q31. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure p against the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. Se figure (3). Fig (3)
The pressure vessel shown below is being lifted by two cables that are attached to the bottom of the tank at points L = 6' away from each other. Assume that this causes reaction forces at the bottom of the tank that are oriented in the direction of the cable, i.e. 30 degrees from vertical. The tank weighs 4,970 lb. For simplicity, assume that the weight is evenly distributed from one connection point to the other, thus ignoring any weight in the end caps. Also assume that the tank is pressurized to 272 psi. The tank has an internal radius of 1.7 ft and a thickness of 1/8 inch. The tank is made out of steel with a 50 ksi yield strength. Determine 1) the combined stress state at point C, which is located at mid-length at the bottom of the tank and 2) the factor of safety against yielding at point C using the Tresca criterion. In your work, be sure to clearly indicate your answers to parts 1 and 2. Please insert the factor of safety.