COMPLETE ALL PARTS PLEASECIRCUIT THEORY The R-C circuit shown below has an AC power supply with 150 Vrms / 50 Hz output.Moreover, R1=8kN, R2=10kN, C,=0.03µF and C2=0.065µF.Perform calculations and type your results in the appropriate number boxes provided. Please note the specific measuring units required foryour numerical answers.The total resistance isΚΩTotal capacitance isnFThe total reactance IsknThe total circult Impedance IsC1R1The phase angle is°[angular degrees]The total current isVsfThe voltage across capacitor C, isThe voltage across capacitor C2 isVC2The voltage across resistor R, isVR2The voltage across resistor R2 ISVThe current through R2 ismAThe current through C, is]:The reactive power in the circuit isMVARThe true power dissipated by the circuit ismwThe total apparent power in the circuit ismVAThe circuit has a power factor of%

The total resistance of the circuit is Req=R1+R2=8K+10K=18KΩ The two capacitors are in series, then…

The R-C circuit shown below has an AC power supply with 150 Vrms / 50 Hz output. Moreover, R1=8kN, R2=10kN, C;=0.03µF and C2=0.065HF. Perform calculations and type your results in the appropriate number boxes provided. Please note the specific measuring units required fo your numerical answers. The total resistance is k2 | Total capacitance is nF The total reactance Is kn The total circult Impedance is Ci R1 The phase angle is °[angular degrees] The total current is

The R-C circuit shown below has an AC power supply with 150 Vrms / 50 Hz output. Moreover, R1=8kN, R2=10kN, C;=0.03µF and C2=0.065HF. Perform calculations and type your results in the appropriate number boxes provided. Please note the specific measuring units required fo your numerical answers. The total resistance is k2 | Total capacitance is nF The total reactance Is kn The total circult Impedance is Ci R1 The phase angle is °[angular degrees] The total current is

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal light
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
a/ What is the function of the inductance L in a single phase halfwave thyristor? b/ A controlled full wave bridge rectifier has a source of 50 Sinwt with R = 10 and L = 20 mH find the d.c load current if a = 40°, then draw Vo and lo use 50 Hz freq. and B = 1.1n %3D