The reaction-rate data given below were obtained using a batch reactor for the reaction A > products. Determine the order of the reaction and reaction rate constant. Using integration method and differential method Time (day) CA (mg/L) 16 4 6 8 10 12 14 15.00 10.05 6.74 4.52 3.03 2.03 1.36 0.91 0.61

The reaction-rate data given below were obtained using a batch reactor for the reaction A > products. Determine the order of the reaction and reaction rate constant. Using integration method and differential method Time (day) CA (mg/L) 16 4 6 8 10 12 14 15.00 10.05 6.74 4.52 3.03 2.03 1.36 0.91 0.61

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter10: Oxidation, Degradation, Corrosion, Electroprocessing, Batteries, And Fuel Cells

Section: Chapter Questions

Problem 10.1P

See similar textbooks

Similar questions

Determine the pH of the solution produced in the reaction flask when 25.00mL of 0.100 M NaOH has been added to 25.00 mL of 0.100 M HCl
Example 3-5 If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order to hold the assembly in the position shown. 30 Solution Free-Bo, Diugram 40 kg TED
Q2: A drop of liguid foluen is kept al uniform temperkure t 299 K and is suspended in air by a fine wire. The initid radius at r= 2mm. The vapor pressure of foluene 299K is f=384 Kfe and the density of liguid toluene is 366 ky Im 3. Derive equation for the time tp for the drop b evupurete Completely in a large volume of still air Calculate the tine in seconds for Complete evaporahion.
Determine reaction
Determine the reaction at A in the given figure. (please submit your solution for this item) * 2 kN/m 600mm- 450 mm 300 mm
(round off to 2 decimal places) is CIC, =0.8, the value of LCMFR/ LR 2 Consider the reactor shown in the figure. of a compound in the influent and The flow rate through the reactor is Q m'/h. The concentrations (in mg/L) effluent are C, and C, respectively. The compound is degraded in the reactor following the first order reaction. The mixing condition of the reactor can be varied such that the reactor becomes either a completely mixed flow reactor (CMFR) or a plug-flow reactor (PFR). The length of the reactor can be adjusted in these two mixing conditions to LCMFR and LPER while keeping the cross- section of the reactor constant. Assuming steady and for state %3D Q, C.
3. Some industrial spent catalyst was tested as adsorbent material in a batch experiment. The data are reproduced in the following table. Determine the Final Conc., Ce (mg/L) 14.88 9.55 1.89 0.58 0.44 0.61 0.36 Uptake, q (mg/g) 8.80 8.41 7.33 6.15 5.68 4.92 3.79 a. Determine the coefficients for these data assuming a Freundlich isotherm applies. b. Determine the coefficients for these data assuming a Langmuir isotherm applies. c. Which isotherm model provides a better fit to the data? Explain.
Consider the reactor shown in the figure. The flow rate through the reactor is Q m/h. The concentrations (in mg/L) of a compound in the influent and effluent are C, and C, respectively. The compound is degraded in the reactor following the first order reaction. The mixing condition of the reactor can be varied such that the reactor becomes either a completely mixed flow reactor (CMFR) or a plug-flow reactor (PFR). The length of the reactor can be adjusted in these two mixing conditions to LCMFR and LPER while keeping the cross-section of the reactor constant. Assuming steady state and for C/C, = 0.8, the value of LoMER/LPER (round off to 2 decimal places) is_ Q, C Co
During a steady flow process, the pressure of the working substance drops from 200 to 20 psia, the speed increases from 200 to 800 ft/s the internal energy decreases 20 BTU/lb and the specific volume increases from 2 to 10 ft³/lb. No heat transferred. Determine the following: a)AKE in ft-lb;/Ibm b)APE in ft-lb/lbm c)AW: (flow work) ft-lb:/lbm d)AH in BTU e) Net work in hp for 15 lb/min of fluid (use mass flow rate for this item only)
4 UEME1233 MANUFACTURING TECHNOLOGY I Hot working is a process commonly seen in the production floor that usually involved heating furnaces. Explain one reason of hot working and justify the types of heat-treating furnaces. Q1. (а) (Word limit: ~150) (b) Discuss the importance of understanding in crystal structure of metal and why different crystal structures exhibit different strengths and ductility. (Word limit: ~150)
Environmental Engineering: A reaction takes place in aqueous solution and is first order. The required degree of conversion is 99% and this takes place in 10 minutes in a batch experiment. a. What would the necessary detention time be in a CSTR? b. What would be the necessary detention time to achieve 99% conversion in a CSTR system using two equal tanks in series?
The analysis of a water sample for MPN calculation in Multiple Tube Fermentation Test is given below: Size of the sample (ml) 1 0.1 0.01 0.001 Number of (+)ve tubes 4 3 3 0 Number of (-)ve tubes The MPN using the Thomas equation is 1 2 2 5