The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 1.5 m |A = 180 mm? L =1 m A = 360 mm2 A В 5 m

The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 1.5 m |A = 180 mm? L =1 m A = 360 mm2 A В 5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

O A rectangular strip 50×15mm deep of brass is placed on top of another strip 50×15mm deep of steel to form a beam of 50×30 mm deep cross-section. The beam is supported across a span of 100 cm. Determine the magnitude of a point load that may be placed at its midspan if (a) The strips separate and bend independently E steel = = 2×10 MPa, Ebras = 0.9×10 MPa, stress are o steel Permissible = 150 MPa and o = 100 MPa brass 100 cm
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E, = 200 GPa and Eb = 105 GPa, determine the deflection of point C. Sc A um →>> Dimensions in mm 120 180130- Steel B 65 KN 40-mm diam. D Brass 120 E 50 KN 30-mm diam.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
Hide bla Clear my choice A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior. |-1 2 m 1.5 m A 3 m 2 m 2 m Select one: 11:49 PM A G d) ENG B
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m
Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 6.8 kN and 8 = 20°. Point O is at the center of the I-beam. 2.4 kN - 630 mm 70 mm 2.2 kN 350 mm 1.0 kN 1.4 kN F Answer: y = mm the tolerance is +/-2%
A steel rod (E=29000ksi) was pulled by a 2kip force. The initial length of the rod is 3ft and the radius is 1in. Solve the deformation. O 0.00079in O 0.00020in O 0.00316in O 0.00119in
The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is horizontal before load P is applied, find the distance x (in meters) that locates the position where P must act if the bar is to remain horizontal. (E of steel 29000 ksi and E of bronze = 83 GPa) Neglect the weight of bar AB. L=2ft Aw02 in? A 0.4 in 1on