The rod ABCD is made of an aluminum for which E= 70 GPa. Take P = 80 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 1.75 m Area = 800 mm2 B 1.25 m C Area = 500 mm2 75 kN 1.5 m 50 kN For the loading shown, determine the deformation of point B.

The rod ABCD is made of an aluminum for which E= 70 GPa. Take P = 80 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 1.75 m Area = 800 mm2 B 1.25 m C Area = 500 mm2 75 kN 1.5 m 50 kN For the loading shown, determine the deformation of point B.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.91 in2, A? = 0.31 in2, P1 = 81 kips, P2 = 47 kips, P3 - 31 kips and E = 29x106 psi %3D %3D Your final answer should have three decimal places A1 A2 B. D' P3 P1 P2 -/- --16 in 12 in. 12 in.
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses OAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aa=23.9*10-6 1/°C, Eal=72GPA //// A 60 mm diameter 1.1 m B 40 mm diameter 1.3 m Aluminum Brass
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (SB) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m B 40 mm diameter 1.3 m C Aluminum Brass
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
4. A piercing punch of a die assembly has a diameter of 20mm and will be used to punch in an aluminum plate with a thickness of 4mm. Knowing that the ultimate shear stress of the plate is 280 MPa, determine the force P required to punch through the plate. Punch Aluminum = 4 mm d=20 mm
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: a,=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m В 40 mm diameter 1.3 m C Aluminum Brass