The shaft shown consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T= 10 kip · in. is applied. Use G= 4 x 106 psi for aluminum and G = 12 x 106 psi for steel.

The shaft shown consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T= 10 kip · in. is applied. Use G= 4 x 106 psi for aluminum and G = 12 x 106 psi for steel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.46 GPa. For the steel segment BC, the diameter is 50 mm and G = 84.51 GPa. Given that a = 2.2 m and b = 1.35 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.01 MPa in the bronze and 83.59 MPa in the steel. Round off the final answer to two decimal places.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
A solid shaft 100 mm in diameter is subjected to an axial compressive load of 600 kN simultaneously with a torque that twists the shaft thru an angle of 1.5 degrees in the length of 8 meters. If G=80Gpa, compute the maximum normal stress in the shaft. This is a COMBINED STRESS problem. Please include drawings of the circle.
1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
The solid compound shaft, made of three different materials, carries the twoTorques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 GPa for bronze
A 45-mm-diameter solid steel shaft supports loads PA-1.2 KN and Pc-2.7 kN as shown. Assume that L₁ - 105 mm, L₂ = 205 mm, and 43-150 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. L₂ C Pc Ly D
A compound steel shaft consists of solid 21-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 42 mm and a wall thickness of 2.3 mm. Assume T = 350 N·m, L1 = 1.4 m, L2 = 1.5 m, and L3 = 1.4 m. Calculate the polar moment of inertia for tube segment (2). Determine the maximum shear stress in tube segment (2).
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa..Power (P) 22 in kW , Speed (N) 550 in Rpm