The slotted arm OB rotates in a horizontal plane about point O of the fixed circular cam with constant angular velocity = 10rad/s. The spring has a stiffness of 6.4 kN/m and is uncompressed when 0-0. The smooth roller A has a mass of 0.36 kg. Determine the normal force N which the cam exerts on A and also the force R exerted on A by the sides of the slot when 8-52°. The force R is positive if contact is with the lower surface. All surfaces are smooth. Neglect the small diameter of the roller. 0.19 0.19 m m HIILE SILLED

The slotted arm OB rotates in a horizontal plane about point O of the fixed circular cam with constant angular velocity = 10rad/s. The spring has a stiffness of 6.4 kN/m and is uncompressed when 0-0. The smooth roller A has a mass of 0.36 kg. Determine the normal force N which the cam exerts on A and also the force R exerted on A by the sides of the slot when 8-52°. The force R is positive if contact is with the lower surface. All surfaces are smooth. Neglect the small diameter of the roller. 0.19 0.19 m m HIILE SILLED

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The uniform slender rod has a mass m= 20 kg and length L = 0.5 m. As the frame accelerates forward the rod is held in the position shown at a steady angle 0 = tan (3/4) by the stop at A. Determine the magnitude of the reaction force at stop A if the acceleration is a = 6 m/s. A = a L. A
The flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm N
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
The spring-held follower AB has a weight of 0.75 lb and moves back and forth as its end rolls on the contoured surface of the cam, where r=0.2 ft and z = (0.1sine) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force at the end A of the follower when e=90°. In this position the spring is compressed 0.4 ft. Neglect friction at the bearing C. z = 0.1 sin 20 0.2 ft e = 6 rad/s k = 12 lb/ft Fs FA- T
At the instant shown, the spring is undeformed. Determine the change in potential energy if the 20 kg disk (radius of gyration = 0.5 m) rolls 2 revolutions without slipping. Note that the shown velocity vector refers to the translation of the centre of the wheel. Choices are in image.
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
Part A The smooth surface of the vertical cam is defined in part by the curve r = (0.2 cos 0+0.3) m. The forked rod is rotating with an angular acceleration of 0 = 2 rad/s as shown in (Figure 1), and when 0 = 45°, the angular velocity is 6 = 6 rad/s. Determine the force the cam and the rod exert on the 1.8-kg roller at this instant. The attached spring has a stiffnesss k = 100 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. ? Neam, Frud = N Submit Request Answer Figure 1 of 1 Provide Feedback Next >
A constant couple moment M is acted on the drum O to pull the spool C up the incline. Both drum O and spool C can be treated as uniform disk. If spool C is rolling without slipping, determine the angular acceleration of the drum and the cord force. R R (0 M
The homogeneous, solid cylinder with mass m = 4.8 kg and radius r = 0.24 m rolls along the inclined surface without slipping. If the initial angular velocity is w, = 2 rad/s (counterclockwise), and after a certain time lapse the angular velocity is w2 = 2.2 rad/s (clockwise), determine the magnitude of the linear impulse due to the frictional force during this time period. Let 0 = 46°.
The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the vertical plane. At the instant when Angle theta = 30°, the velocity of roller A is 13 ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G and the reactions of points A and B, under the action ofthe 6-lb force P. Neglect the friction and the mass of the small rollers.
The 24-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r= 0.4 m. When the wheel is subjected to the couple moment M = 90 N•m, it slips as it rolls. Determine the linear acceleration of the wheel's center O (in m/s?). The coefficient of kinetic friction between the wheel and the plane is Uk = 0.45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M