I need the answer quickly The specific name for the AC-to-DC converter is:DC Chopper1А.В.RectifierС.InverterD.Controller2The SCR turns OFF when its current reduces below.. for sufficient time.A.The reverse current, IRВ.The holding current, IHThe latching current, ILThe gate current, IGС.D.A pure DC quantity a ripple factor of:A.141.4%В.70.7%С.1D.4"A diode of 600V voltage rating" meansA.The peak reverse voltage is 600V.В.The maximum average voltage is 600V.C.The peak forward voltage is 600V.D.The maximum RMS voltage is 600V.The following device is available with highest voltage and current ratingsА.Shottkey diodeВ.SCRC.IGBTD.BJT6The following power switching device is controlled by voltage signal:A.BJTВ.GTOС.SCRD.MOSFET7A converter operated in fourth quadrant if:vo negative and io positivevo and io are negativevo is positive and io is negativevo and io are positiveGiven V1,dc=175V, and V2,dc=75V; then (V1+V2)dc=Could be 250V or 100VА.B.C.D.8A.В.250VС.Impossible to calculate from the information given.D.190.39VThe following parameter determines the quality of inverter output:A.The ripple factorВ.The form factorС.The total harmonic distortionD.The power factor10Given V1,dc= -12V, and V1,ac%3D16V; the RMS of V1=A.28VВ.10.58VС.4VD.20V

1) To connect AC to DC we use rectifier. Ans. Rectifier.

The specific name for the AC-to-DC converter is: А. DC Chopper В. Rectifier С. Inverter D. Controller 2 The SCR turns OFF when its current reduces below. for sufficient time. A. The reverse current, IR В. The holding current, IH С. The latching current, IL D. The gate current, IG 3 A pure DC quantity a ripple factor of: A. 141.4% В. 70.7% с. 1 D.

The specific name for the AC-to-DC converter is: А. DC Chopper В. Rectifier С. Inverter D. Controller 2 The SCR turns OFF when its current reduces below. for sufficient time. A. The reverse current, IR В. The holding current, IH С. The latching current, IL D. The gate current, IG 3 A pure DC quantity a ripple factor of: A. 141.4% В. 70.7% с. 1 D.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A. Determine the: i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI, iv. peak current of the transistor, Ip, V. critical values of L and C, and vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. is Vs C Load Vo, Vs VC i, Ia Figure 2
8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
Investigate the operation principle of 3- phase inverter for 120°-Δ conduction interval (by sketching phase-to-phase and phase-to-neutral voltages and terminal currents).
Q2. A) What are the main differences between the three-phase bridge 180 and 120 degree modes of conduction? B) What is a single-phase current source inverter?
Explore the advancements in microchip fabrication technology, such as FinFET transistors and Moore's Law. How have these advancements influenced the performance and power efficiency of microchips?
4) Choppers is a a. AC - DC converters b. AC - AC converters c. DC - AC converters d. DC - DC converters 5) A single phase dc ac converter is also known as a. Rectifier b. Inverter c. Chopper d. Regulator
1-Write the characteristics of NTC.? 2-Draw the Characteristic curve of PTC.?
FETs have similar properties to ___. a. Scotty diodes b. NPN transistors c. PNP transistors d. uni-junction transistors