The spool of cable has a mass of m and a radius of gyration of ke. The tension in the cable T is a function of time t, when t is in seconds. Neglect the mass of the unwound cable, and assume it is always at a constant radius. a.) What is the moment of Inertia of the spool? b.) What is the angular acceleration of the wheel at t (Use + for the ccw direction)? c.) How quickly is the cable being pulled at time t (Use + for to the right) in m/s? do h d₁ 0 = 60° Variable do d h kc Ethe m T Value 1m 0.5 m 2.25 m 0.77 m 100 kg 30t³ +77t N 1.81 s 135i + 0) N

The spool of cable has a mass of m and a radius of gyration of ke. The tension in the cable T is a function of time t, when t is in seconds. Neglect the mass of the unwound cable, and assume it is always at a constant radius. a.) What is the moment of Inertia of the spool? b.) What is the angular acceleration of the wheel at t (Use + for the ccw direction)? c.) How quickly is the cable being pulled at time t (Use + for to the right) in m/s? do h d₁ 0 = 60° Variable do d h kc Ethe m T Value 1m 0.5 m 2.25 m 0.77 m 100 kg 30t³ +77t N 1.81 s 135i + 0) N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) Find the final speed V of the center of mass of the wheel once the wheel starts moving.
1.) What is the moment of inertia of the object about an axis at the center of mass of the object? (Note: the center of mass can be calculated to be located at a point halfway between the center of the sphere and the left edge of the sphere.) 2.) If the object is fixed at the center of mass, what is the angular acceleration if a force F = 489 N is exerted parallel to the rod at the end of rod?
A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating masses of the engine have an angular speed of 100 rad/s in clockwise direction when viewed from the front of the car The combined moment of inertia of the rotating masses is 10 kg-m².what is the magnitude of the gyroscopic moment in (N-m)?
Paragraf Stiller Düz 11 In Figure 2, the wheel with mass p (kg) with an inertial radius of kA (mm), M-X.t (N.m) it has been subjected to moment (t seconds). Starting from a stationary state calculate the angular speed of the wheel after t1 seconds. Also, the reaction force that the fixed bearing a exerts on the wheel during movement calculate. (Gravity acceleration will be taken as 9.81 m/s2.) kA= 252 mm p= 13 kg x= 3 t;=2 M Odak
The mass of flywheel of an engine is 8 tonnes and the radius of gyration is 1.8 metres. It is found from the turning moment diagram that the fluctuation of energy is 100 kN-m. If the mean speed of the engine is 150 r.p.m., find the maximum and minimum speeds.
The wheel shown below has a mass of 5 slugs and a radius of gyration for the z-axis through point Cof 0.7 ft. The spring is massless and has a modulus of 20 lb/ ft and a natural (unstretched) length of 4 ft. Use the acceleration due to gravity, g = 322 ft/sec. The wheel is released from rest, and it rolls without slipping on the plane. Find how far down the plane the mass center Cwill move. Cord wrapped ´around hub IT 1.3 ft 0.8 ftC 3 ft 3 4 0.5 ft
Calculate the center of mass acceleration of the cylinder rolling down the inclined plane in the below figure for the case of no slipping. Choose an axis that passes through the point of contact. Will need to determine the moment of inertia of the cylinder about this point. FP FN
Important problem. The motor produces a counterclockwise torque 1 N.m on the attached disk A. A Part of this torque is transferred to the disk C through the belt after amplification. The disk A has mass 0.5 kg. and the disk C has mass = 4.5 kg. Find: (50 m 5omm pully C I. The difference tension between the palley A Te belt parts (7- T). II. The angular acceleration of the disk С. The angular acceleration of disk A. The angular velocity of the disk C after 5 seconds from the motion start. The transferred torque to the disk C. III. IV. V.
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
What is the angular acceleration at point BC What is the total Acceleration at Point B? At Point C? Draw the force and inertia diagram.
3. The spring-toggle system is in the vertical plane and is held at rest with 45° when a moment of 12 N-m is applied at point C. In the initial position, the spring, with stiffness of 140 N/m, is stretched 150 mm. Bar AB has a mass of 3 kg, and bar BC has a mass of 6 kg. Find the angular velocity of BC at the moment when 8-0. Neglect friction effects. 250 mm 250 mm OB 250 mm
An aeroplane runs at 600 km/ h. The rotor of the engine weighs 4000 N with radius of gyration of 1 metre. The speed of rotor is 3000 rpm in anticlockwise direction when seen from rear side of the aeroplane. If the plane takes left turn in a curve of 100 metres radius, find: 1. gyroscopic couple developed; and 2. effect of reaction gyroscopic couple developed on the body of aeroplane by using vector diagram.