The state of plane strain on an element has components of Ez = 500 (10-6), y = 300(10-6), and Yzy-200(10-6). (Figure 1) Figure Edy dy Yxyf dx €₂dx 1 of 1 > Part A Determine the equivalent state of strain on an element at the same point oriented 45° clockwise with respect to the original element Enter your answers to three significant figures separated by commas. Ez, Ey, Yz'y = 97| ΑΣΦ.11 | vec Submit Request Answer Provide Feedback ? Next >

The state of plane strain on an element has components of Ez = 500 (10-6), y = 300(10-6), and Yzy-200(10-6). (Figure 1) Figure Edy dy Yxyf dx €₂dx 1 of 1 > Part A Determine the equivalent state of strain on an element at the same point oriented 45° clockwise with respect to the original element Enter your answers to three significant figures separated by commas. Ez, Ey, Yz'y = 97| ΑΣΦ.11 | vec Submit Request Answer Provide Feedback ? Next >

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.13P: An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 ×...

See similar textbooks

Similar questions

- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A bungee cord that behaves linearly elastically has an unstressed length L0= 760 mm and a stiffness k = 140 N/m. The cord is attached to two pegs, distance/? = 380 mm apart, and is pulled at its midpoint by a Force P = 80 N (see figure). (a) How much strain energy U is stored in the cord? (b) What is the displacement Scof the point where the load is applied? (c) Compare the strain energy (with the quantity PSC12. Note: The elongation of the cord is not small compared lo its original length.
On the free surface of a component, a strain rosette was used to obtain the following normal strain data: €a = 300µɛ, ɛp = 400µs, and Ec = 200µe. Calculate the normal and shear strains in the x-y plane.
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.