The steel shaft is made from two segments AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G-10.8 (10¹) ksi. (Egure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. 195.ΑΣΦ. 41 | voc TRAX Submit Request Answer Provide Feedback ? ksi

The steel shaft is made from two segments AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G-10.8 (10¹) ksi. (Egure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. 195.ΑΣΦ. 41 | voc TRAX Submit Request Answer Provide Feedback ? ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.3P: A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A TB = 180 N-m Tc = 15 N-m TD= 35 N-m DAB DAB = 35 mm DBD = 25 mm G = 170 GPa TB DBD C Tc TD The solid shaft is fixed at A and free at D. It is subjected to three concentrated torques at B, C and D. Determine the magnitude of the maximum stress in the shaft. Ignore stress concentrations. D
Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880 N and T=432 N. The maximum bending moment is at x= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm T, 280 mm 30-mm dia. T, 300 mm 250-mm dia. 400-mm dia. 270 Nx 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. : b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. (; c) Determine the fatigue factor of safety of the rotating shaft with the current dimensions using the DE-Gerber criteria. Use Eqs. 6-8 and 6-18 to find the endurance limit, account only for ka and k, in Eq. 6-18 and assume all remaining factors…
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
This engine is used in a hoist. Motor 2.5 kWwith the help of gears with a power of and n = 500 rpm.transmits. If the shear strength of the AB shaft is τa = 160 MPa;a) Find the diameter of AB shaft with 1.4 times safety.b) Find the maximum force F the engine can carry.
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the figure. Determine the maximum permissible value of T subject to the following design conditions: F.S. = 1.5, Tult steel = 95 MPa, Tult aluminium = 70 MPa, and o < 6° (9 is the angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminium
Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m?
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.