The strut on the utility pole supports the cable having a weight of P = 300 lb. (Figure 1) Figure 1.5 ft 4 ft 1 of 1 2 in. HT COI4 in. Part A Determine the absolute maximum bending stress in the strut if A, B, and C are assumed to be pinned. Express your answer in kilopounds per square inch to three significant figures. VO ΑΣΦ omax = Submit Provide Feedback Request Answer vec ? ksi

The strut on the utility pole supports the cable having a weight of P = 300 lb. (Figure 1) Figure 1.5 ft 4 ft 1 of 1 2 in. HT COI4 in. Part A Determine the absolute maximum bending stress in the strut if A, B, and C are assumed to be pinned. Express your answer in kilopounds per square inch to three significant figures. VO ΑΣΦ omax = Submit Provide Feedback Request Answer vec ? ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A beam is shown in the figure below. Part A If M = 1 kip/ft, determine the resultant force the bending stresses produce on the top board A of the beam. Express your answer to three significant figures and include appropriate units. F = NA Submit Value 3 → Request Answer Units ? o 6 in. 1 in.. 6 in. 1.5 in. 12 in. M 1.5 in.
The beam in (Figure 1) is made from three boards nailed together as shown. Part A If the moment acting on the cross section is M = 560 N · m, determine the resultant force the bending stress produces on the board. Express your answer to three significant figures and include appropriate units. HÀ F = Value Units Submit Request Answer Figure 150 mm 20 mm 200 mm M 20 mm
The beam is supported by a pin at point A and a roller at point C. A distributed load is applied to the beam. Neglect the weight and thickness of the beam. Hints: 1. will need to use similar triangles to find the height after sectioning at B. 2. Review direction of normal force, shear force and bending moment and which is positive or negative. W2 W1 A di d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value W1 190 N-m W2 440 N-m di 5 m d2 5 m a. Determine the magnitude of the normal force at point B, NB. . b. Determine the magnitude of the shear force at point B, VB- c. Is the shear force VB a positive or negative shear force? d. Determine the magnitude of the bending moment at point B, MB. e. Is the bending moment MB a positive or negative bending moment? Round your final answers to 3 significant digits/figures.
Solve the problem shown below. Each answer is worth equal credit. Show all necessary steps of your work clearly to obtain credit. Final answer must be to 3 significant figures and contain units and be in the box. Using P1= 6.0 kips, then determine the reactions and member forces of the truss. a) List reactions at A and K? (Use positive, +, to indicate a reaction that is up, to the right, and counterclockwise.) [30 pts] RAX: RAY: Rkx: Rky: b) Determine the member forces using either the method of joints or method of sections. (Include Units and the correct sign in the answer, (Use: '+'= tension, & '-' = compression) J I H G 4 ft K A -3 ft- B P1 -3 ft- C P1 -3 ft D P1 E -3 ft 3 ft- P1 P1 F FBC: FCJ: FI: FEG: FDH: FIC:
Question 4 Sketch bending moment diagram for the loading acting on the beam as shown in Figure Q4. From your results, calculate area required for tensile reinforcement using M the formula 4, You may use fyk = 500 MPa and z = 1400 mm. 0.87 fyk 90 kN/m 30 kN/m 200 KN 20 kN/m Danim 100 kNm 2m 5m 3m Figure Q4
A 0.5kg weight is hung from the end of a cantilever beam, causing a vertical displacement of y = -0.01 inches relative to no load. The weight is increased to 1.0kg. What is the new displacement relative to no load? Typed and correct answer please. I ll rate
Answers are already given. Kindly answer all the required forces. ANSWER: FFG=1103.7267 kip, T W= 832. 7498 kip, T Mc= 6272.9979 kip-ft, clockwise Cx= 0 Cy=1297.7498
M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support (triangle)? 3 ft Y-direction for the pinned support (triangle)? 2 ft For the beam above, what are the support reaction forces? Please report your answers in the units of 'kips' and to 2 significant digits (i.e. two decimal places). 6 in 9 in
Problem #8: For the beam and loading shown below compute the state of stress at point B (components of the 3x3 matrix), report your answer in ksi to two decimal places. 1.5 in 1.5 in B l in F= 5 kip 3 in 1 in 15 in Fx = 4 kip 3 in Fy = 3 kip
The beam supports the triangular distributed load shown below with Wmax = 900 lb/ft. The reactions at A and B are vertical. (Figure 1) Figure AT PORCE 6 ft D 6 ft C 6 ft W IB TODAY E 4.5 ft 4.5 ft Part A Determine the magnitude of the resultant internal normal force on the cross section at point D. Express your answer in kilopounds to three significant figures. ND= Submit Part B Vp= Submit Part C ΠΙΑΣΦΗΜ Mp= Avec Submit Request Answer Determine the magnitude of the resultant internal shear force on the cross section at point D. Express your answer in kilopounds to three significant figures. ΠΙΑΣΦΩΤ Request Answer n Request Answer vec 1 → C vec S S ? Determine the magnitude of the resultant internal bending moment on the cross section at point D. Express your answer in kilopound-feet to three significant figures. [Γ]ΑΣΦ [4 O I ? kip ? kip kip.ft
Part B Draw the moment diagram for the shaft. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. 600 N-m 0.8 m 0.8 m 0.8 m No elements selected 900 N M (N m) 1000 900 800 700 600 500 400 300 200 100 I (m) 0+ -1000.0 0.2 0.4 0,6 0,8 1.0 12 1.4 1.6 1,8 2.0 2.2 -200 + -300 -400 -500 -600 -700 -800 -900 -1000 Add discontinuity lines and select segments to add to the canvas.