The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the require area of reinforcement given a 10% redistribution of moments was applied in determining the moment. stic material strengths: concrete inforcement Width of flange Height of flange Width of web fcu:= 30-MPa fy:= 450 MPa bf:= 400-mm hf:= 100-mm bw := 200-mm d:= 350-mm Reinforcement Depth bf A bw d

The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the require area of reinforcement given a 10% redistribution of moments was applied in determining the moment. stic material strengths: concrete inforcement Width of flange Height of flange Width of web fcu:= 30-MPa fy:= 450 MPa bf:= 400-mm hf:= 100-mm bw := 200-mm d:= 350-mm Reinforcement Depth bf A bw d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameters bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 Mpa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm Depth of uniform stress block at ultimate stage in mm to the nearest whole number Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
Seatwork The beam shown is prestressed by using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons strength fpu=1350 MPa, fc'=35 MPa. The area of prestressed reinforcement in tension zone Aps=1000 mm?. The specific yield strength of prestressing tendons sd, foy=1160 MPa. а. What is the value of the stress in prestressed reinforcement at nominal strength (Aps) b. What is the value of the depth of the compression block. С. What is the ultimate moment capacity of the prestressed beam. 0.85fc' 430 NA |(d-a/2) · A=1000 T=Ap.Sps 250
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
A reinforced concrete T – beam is to be designed for tension reinforcement only. The beam width is 250 mm and the effective depth is 400 mm. The flange thickness is 100 mm and its effective flange width is 900 mm. The applied moment is 300 kN–m. What is the area of tension reinforcement required? use: fc’ = 20.7 MPa and Fy = 414 MPa. * a. 3 983 mm² b. 5 105 mm² c. 2 166 mm² d. 4 094 mm²
A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a". %3D
A simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam. Concrete covering to centroid of reinforcement is 70mm at the top and 64 mm at the bottom. The beam has a gross depth of 450 mm and gross width of 300 mm. Fc’=28 mpa fy= 415 mpa. Assume bars are laid out in a single layer. calculate the following if the limiting tensile steel strain is 0.004 for ductile failure: a) depth if neutral axis from the extreme concrete compression fiber ( in mm, in whole number) b) design strength of the beam section ( in kn•m , in whole number) c) maximum service uniform live load over the entire span in Addition to a DL = 20 kn/m ( including weight of the beam) if it has a span of 6 m ( in kn, in whole number)
A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-020 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 8.003 in 3 decimal places =
Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
fe= 3000psi fé's 4 fy = 60 steel 4 %3D 18" 4 #8 NWC Mer= ? M 50 ft-K. Please Compute the bending stresses in the bec by Using transformed - area method.
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D