The temperature of 1.9 kg of water is 100.0°C, but the water is not boiling, because the external pressure acting on the water surface is 3.0 x 105 Pa. Using the vapor pressure curve for water given in the figure, determine the amount of heat that must be added to the water to bring it to the point where it just begins to boil. Pressure, Pa 4 x 105 3x 105- 2x 105- 1.01 105 0.53 105 0 83 100 Temperature C 100 C 150 1.01 105 Pa 83 C 0.53 x 105 Pa Storage settings

The temperature of 1.9 kg of water is 100.0°C, but the water is not boiling, because the external pressure acting on the water surface is 3.0 x 105 Pa. Using the vapor pressure curve for water given in the figure, determine the amount of heat that must be added to the water to bring it to the point where it just begins to boil. Pressure, Pa 4 x 105 3x 105- 2x 105- 1.01 105 0.53 105 0 83 100 Temperature C 100 C 150 1.01 105 Pa 83 C 0.53 x 105 Pa Storage settings

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the diagram, the state of helium gas is changed in such a way that its PV graph is a straight line segment with volume Vo increases to yVo and pressure Po increases to xPo where x and y are arbitrary constants. During this process the total heat transferred to the gas is equal to the heat necessary to double the absolute temperature of the gas at constant volume. What is the maximum ratio for the volume increase? xP, P. Vo
A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi gauge and 82°F. After some amount of acetylene was used, the pressure was reduced to 190 psi gauge and the temperature was 74°F. The gas constant of acetylene is 59.35 ft-lb:/lbm-°R. Determine the following: 1. What is the initial mass in Ibm of the acetylene inside the vessel? 2. What proportion in percentage of acetylene was used? 3. What volume in ft would the used acetylene occupy at 30 psig and 80°F?
1:09 O71VON 2_53057102948... -> Q/ A dry gas reservoir is initially at an average pressure of 5500 psia and temperature of 145F. The gas has a gravity 0.67. What will the average reservoir pressure be when 40% of the original gas(in Scf) has been remained in the reservoir. Assume the volume occupied by the gas in the reservoir remains constant. If the reservoir originally contained 1MM cuft of reservoir gas, how much gas has been produced at a final reservoir pressure of 600 psia.
A 2-kg steam water mixture at 1.0 MPaa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPaa and the temperature to 400 oC. Determine: a) Heat transferred (kJ), b) ΔH(kJ), c)ΔS (kJ/k) PLS PLS SHOW COMPLETE SOLUTION WRITE LEGIBLY AND ROUND OFF TO 4 DECIMALS INCLUDE P-S AND AND T-S DIAGRAMS PLS PLS REFER THE STEAM TABLE ATTACH FOR THE VALUES
A 2-kg steam water mixture at 1.0 MPaa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPaa and the temperature to 400 oC. Determine: a) Heat transferred (kJ), b) ΔH(kJ), c)ΔS (kJ/k) PLS PLS SHOW COMPLETE SOLUTION WRITE LEGIBLY AND ROUND OFF TO 4 DECIMALS INCLUDE P-S AND AND T-S DIAGRAMS PLS
An oxygen tank has a volume of V = 3.00 m3. The gage pressure of oxygen in the tank is Pgage = 400.00 kPa. The room temperature is T = 27.00 ˚C and the atmospheric pressure is Patm = 100.00 kpa. The gas constant of oxygen is R = 0.25980 kPa/(kg·K). Oxygen can be treated as an ideal gas. Determine (1) the specific volume of oxygen, v =_____ m3
An oxygen tank has a volume of V = 3.00 m3. The gage pressure of oxygen in the tank is Pgage = 400.00 kPa. The room temperature is T = 27.00 ˚C and the atmospheric pressure is Patm = 100.00 kpa. The gas constant of oxygen is R = 0.25980 kPa/(kg·K). Oxygen can be treated as an ideal gas. Determine (2) the mass of oxygen, m =_____ kg
Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
Using the following information, determine the vapor pressure of water at 300 °C. Note: We started this problem in week 6 lecture 3. Please refer to the lecture to get started on this problem. You only need to show your work starting from where the lecture left off. H₂0 at T = 179.88 degrees C the vapor pressure is PSAT = 10 bar. The enthalpy of vaporization is 2014.59 kJ/kg V = 0.1944 m³/kg V¹ = 0.001127 m³/kg The equation we left off on in class was, cpf 1 [P² psat dpsat pi psat Tf 1 ∆vapH (TF 1 RAZ Ti dT T2a
Water boils at 100°C at atmospheric pressure, that is, at sea level (To=15ºC). The boiling point is defined as the temperature at which the vapor pressure of water is equal to the atmospheric pressure. This has consequences for cooking in places such as Atok where it takes quite a bit longer to make a hard-boiled egg than it would in Baguio City. If the albumen in an egg needs to reach 75°C for the protein to coagulate, at what height would it be impossible to hard boil an egg?
1. The flash point of an engine oil is 3630F. What is the absolute flash-point temperature in K and R is
A piston cylinder assembly contains water. Heat is transferred to the cylinder in order to heat the water. The atmospheric pressure is equal to 100 kPa. Determine the boiling temperature of water if the mass of the piston is equal to 1000 g. Consider g= 10 m/s^2. The cross sectional area of the piston is equal to 100 cm^2. Select one: O a. 102.3 C O b. 97.92 C O c. 99.9 C O d. 103.4 C