The three principal stresses at a given point are σ1 =60 MPa, σ2 =−100 MPa, σ3 =−10 MPa. If the material has a yield stress of 250 MPa, estimate the factor of safety against yielding using (i) the maximum shear stress theory and (ii) von Mises’ theory.

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given data:- do=75 mmt=5 mmT=2410 N⋅mG=80 GPaL=2 m   It is required to determine the angle of twist…

Q: A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of…

A:

Q: - Draw the Mohr's Circle of the stress element shown in figure. Find: - The stresses acting on…

A: the following data is given-

Q: Q5 It was found experimentally that a certain material does not change in volume when subjected to…

A: when a body is subjected to elastic state of stresses, then the strain in the three mutual…

Q: Determine the Reactions 8 kN 2 kN/m BIC 3m 3m2m-3m- D m

A: According to the given data, all the free-body diagram are drawn below We need to find  Reactions

Q: 5-67. The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three…

A: The uniform concrete slab has a mass, m =2400 kg. The weight uniform concrete slab, W = mg. To find:…

Q: In an air-conditioning unit 3.5 m3/s of air at 28 C dry-bulb temperature, 50 percent  relative…

A: Given-Information:- Volume, v = 3.5 m3/sTemp, T = 28°CRelative Humidity, RH = 50%..InletDry-Bulb…

Q: QUESTION 4 In the figure, a homogeneous, planar plate with a constant thickness is given on the…

A: The thickness is constant.

Q: Blocks A and B have masses of 200 kg and 100 kg, respectively. They rest on a 30° inclined plane and…

A: Here, given that, Mass of block A, mA = 200 Kg Mass of block B, mB = 100 Kg We have to find…

Q: For Problems 1-6, design a bolted joint to join the two mem- bers shown in the appropriate figure.…

A:

Q: If the hub gear H and ring gear R have angular velocities Wh = 5rad/s and Wr = 20rad/s,…

A: According to the given diagram, the arm OA rotates about a fixed point O. Draw a diagram showing the…

Q: HW #2 Derive T(r) with k=ko (1+BT) for cylinder. T₁ 12 BC. T(r₁) = T₁

A: GivenTr1=T1T(r2)=T2k=ko1+βT

Q: P6-18 Air flowing at 0.5 m³/min enters à compres kPa and 25°C. The air exits at 600 kPa and 300°C.…

A: Air flow rate = 0.5 m3/min =0.00833m3/s At entry pressure = 101 kPa At entry Temperature = 25°C=…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 214 mm and a…

A: Given For segment (1)           Outer diameter do1=214 mm=0.214 mWall Thickness t1=10 mmInternal…

Q: The following figure represents a bicep curl maneuver where the center of mass (CoM) of a 23 kg…

A: The mass of the arm, m = 5 kg The mass of the dumbbell, M = 23 kg

Q: ure 2 ft 1 ft Part A Determine the angular velocity of the spool. The cable wraps around the inner…

A:

Q: Two 55-kg crates are located on a horizontal ground. Force Pis applied to the crate P as shown in…

A:

Q: Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal…

A: input speed, N1 = 1750 rpm output speed, N2 = 725 rpm linear velocity, v = 4000 ft/min

Q: Power-to-X project or commonly known as Projekte Kopernikus in Deutschland, is a process involving…

A: To Find : The flow reactor with the correct reactor volume to achieve 90 mol% CO₂ conversion.  Given…

Q: In the diagram below, m is an external mass applied to the Truss. Given the information provided in…

A: In the diagram below, m is an external mass applied to the Truss. Given the information provided in…

Q: 8-41. Specify a suitable wide-flange beam to be made from ASTM A992 structural steel to carry the…

A:

Q: 12.5 Air initially at 50 psia and 660°R expands to atmospheric pressure. The process by which this…

A: Given Data: p1=50 psiaT=660oRpV1.3=Cp2=14.7 psia   To Find: (a) Final temperature. (b) Change in…

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: h0=2.4 mρ=1000 kg/m3Qi=0.24 m3/sQo=0.01 m3/st=100 sA=5 m2

Q: Ex Yxy Yyx 3.3.2 Drawing the Mohr's Circle Example: - Ex = 70με &y = 40με Yxy = 60 με لاوه لان Yyx…

A: Given data:- εx=70 με (Tension) εy=40 με (Tension) γxy=60 με (Positive) To draw:-Mohr's Circle

Q: 20 mm. 20 mm 4. The simply supported beam on the right is built up from three boards by nailing them…

A: Given data  Load = 12 kN  Force resisted by the nails = 1.5 kN  Find the maximum allowable spacing…

Q: (1) cord A 60° B JIN G 8 JIN C bbck: W₁ = TBD :Sassume it's uniform. (→ 6 = cent of gray) 6: W²₁₂ =…

A: It is given: Weight of the rod BC→WBC=8 lb Coefficient of friction→μ=0.40 The free body diagram of…

Q: A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of…

A: U1=2.3 m/sA1=?U2=0.7 m/sA2=11 cm2θ2=30oU3=0.9 m/sA3=8 cm2θ3=25oρ=1000 kg/m3

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support…

A: For a beam to be in stable position:- Summation of all horizontal forces must be zero,Fx=0.…

Q: If the motor of the electric drill turns the armature shaft S with an angular velocity of w = (80t…

A: the angular velocity  ω=80t12to find ω  when N=220 rev

Q: Consider the tripod in (Figure 1). Figure 15m 2m 2m 2.5m < 1 of 1

A: Solution: The coordinate of the points are : A=(0,2,0)B=(3.5,2.5,0)D=(2.5,2,4) The direction cosine…

Q: Knowing that a beam of the cross section shown is bent about a vertical axis and that the bending…

A:

Q: For a closed section beam with thin walls, which of the following options is best to give the least…

A:

Q: Stress Example; The inclined element in the figure is subjected to a compressive force of 3000 N.…

A:

Q: 2. Determine the maximum force P that can be exerted on each of the two pistons so that the…

A: Given: The radius of the piston is R=45 mm. The wall thickness is t=2 mm. The circumferential stress…

Q: (NUMBER 4.) solve for Lm, Pm, and Wm. I’ve attached a reference image with the solution method, I…

A: Given: W=LPEq^L=Ctq^=W3Pμ'Lq^=QinL To find: Lm, Pm, and Wm

Q: The inclined block A is given a constant large rightward acceleration a. Determine the range of…

A:

Q: 50 kips 6 ft B 560 kip-ft 10 ft 6 ft D 20 kips/ft 12 ft EO 6 ft F

A: The magnitude of vertical reaction at any support is equal to the height of the shear force diagram…

Q: 3. Determine the magnitude and location of the equivalent resultant force. Express the results in…

A: To find: The magnitude and location of the equivalent resultant force. Express the results in terms…

Q: If link AB of the four-bar linkage has a constant counterclockwise angular velocity of 21 rad/s…

A:

Q: Freehand sketch a set of front/top/right views

A: According to the given data A 3D object is given We need to draw Three projection view of the object…

Q: Suppose that P = 1400 lb and P₂ = 1700 lb. (Figure 1) Figure 15 A + 15 ft 1 of 1 ARRIEEN 20 ft-20…

A:

Q: Consider the beam shown in (Figure 1). Solve this problem using the conjugate-beam method. Take E =…

A:

Q: An opaque surface with the prescribed spectral, hemispherical reflectivity distribution is subjected…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: ● . At a point on the surface of a component a 60° strain gauge rosette measures & = 0.00046…

A:

Q: Page 428. Sample Problem 6.1.Solve this problem completely;but replace theapplied point-forceon the…

A: The cross section dimension are The I of the section is 8.63*10-6 m4 The centroid location from top…

Q: At a given instant A has the motion shown in (Eigure 1). Figure 3 ft 1.5 ft PA-3 ft/s a-681/8² 1 of…

A: The disk does not slipso that,a0=αr=6×0.5=3m/s2By using relative acc. equation-ac=a0+α×r-ω2r…

Q: An aluminium plate containing an edge crack 29.8 mm long is stressed to 30 MPa. If the crack…

A: edge crack length, a = 29.8 mm = 0.0298 m stress, σ = 30 MPa crack geometry parameter, Y = 1.2

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.