The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint O. Determine the magnitude of the resultant R of the two forces and the angle which R makes with the positive x-axis. The angle 0 is measured counterclockwise from the positive x-axis. 4.1 kN 2.0 KN- Answers: R= i 0= i 37° 519 KN

The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint O. Determine the magnitude of the resultant R of the two forces and the angle which R makes with the positive x-axis. The angle 0 is measured counterclockwise from the positive x-axis. 4.1 kN 2.0 KN- Answers: R= i 0= i 37° 519 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in member CG. The force is positive if in tension, negative if in compression. Assume F1 = 12 kips, F2 = 9 kips, F3 = 12 kips. %3D н 10° G 10' F 10' E 10' A B F, F, F, Answer: CG = i kips %3D
67. A single angle in tension is connected by one leg only. If the areas of connecting and outstanding legs are respectively a and b, then what is the net effective area of the angle? 1sdm b b (a) a- - (b) a+ b. b 1+0.35- a a b (c) a- (d) a+ b 1+0.2- a 1+0.35- b 1+0.2- b a
MESEX B 200 mm Find the distance x(mm) if the bar should still be parallel with the horizontal even after applying a 3000 N load. The Steel Rod AB has a length of 1.5 m, cross sectional area of 85 mm^2, E = 200 000 Mpa. The support at C has a length of 0.51, Area of 115 mm^2, and E= 150 GPa. 3000 N
5 kN Use the method of Joints. Determine the В 3 kN force in each member of the truss and state if the members are in tension or compression. 3 m 45° А D 3 m E 3 m BC = CD
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
DETERMINE ALL THE FORCES SHOW FBD
Question 1: The truss is subjected to the system of forces as shown in the following figure. The truss Is supported bya pin at A and a pin at E. Determine, using the method of joints, the force in members (BA), (BE), and (DE) of the truss and Indicate if these members are in tension (T) or compression (C). Set P P2 = 4 kN. 30 30° D. 3 m 3 m
Replace the loading on the frame by a single resultant force. Suppose that F = 600 N, a = 0.6 m, and h = 1.1 m. Determine the magnitude of the resultant force. Determine the angle between the resultant force and the xaxis. Specify where its line of action intersects a vertical line along member AB, measured from A. h 200 N B a a 200 N C 600 N
From the given set of forces shown, the three forces acting on the beam can be replaced with a single equivalent Force R. Determine the following: P,= 25ヒN Pz - 40KN Pa- 80 kN 40° 500 4m Com a. The x-component of the resultant force? b. The magnitude R. c. The corresponding value of e.
Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if P 9 kN. Sign convention is tension positive and compression negative. Be sure to include units in kilo-newtons as part of your answer! H B 4 m-+ 4 m 5 kN a 4 m F P D 4 m 2 m 4 m E
Q1. The force acting on the gear tooth is F = 20 N. Resolve this force into %3D two components acting along the lines (a-a) and (b-b). F. 60
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 x 106 psi, the deflection of point C will be 0.1 in. A 1.25-in. diameter 4 ft B d 3 ft P 7. Determine the deformation of segment AB in inches if P = 44 kips.