The uniform column consists of an 8-ft section of structural tubing having the cross-section shown. a) Using Euler's formula and a factor of safety of two, determine the allowable centric load for the column and the corresponding normal stress. b) Assuming that the allowable load, found in part a, is applied at a point 0.75 in. from the geometric axis of the column, determine the horizontal deflection of the top of the column and the maximum normal stress in the column.

The uniform column consists of an 8-ft section of structural tubing having the cross-section shown. a) Using Euler's formula and a factor of safety of two, determine the allowable centric load for the column and the corresponding normal stress. b) Assuming that the allowable load, found in part a, is applied at a point 0.75 in. from the geometric axis of the column, determine the horizontal deflection of the top of the column and the maximum normal stress in the column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using integration method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*10% KN.m? “4m e | Sm
A beam is subjected to equal bending moments of M₂ = 3300 N-m. The cross-sectional dimensions are b = 190 mm, c = 26 mm, d = 75 mm, and t = 5 mm. Determine: (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ N y| M₂ (typ) Z- b H K d
The cantilever beam has a steel cable of circular cross-section area at the end. What is the area of the cable’s cross section area if there is no observed deflection at point B? The modulus of elasticity of both beam and cable is 200GPa, and the beam is a steel section with I = 120 x 106 mm4 (Hint: recall axial deformations) USE THE DOUBLE INTEGRATION METHOD.
The rigid bar DEFis welded at point D to the uniform steel beam AB. For the loading shown in figure 5, determine (a) the equation of the elastic curve of the beam, (b) the deflection at the mid-point C of the beam by double integration method Use E=29x106 psi and I= 2000 in4 X=4740
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
The cross-sectional dimensions of a beam are shown. Assume b=2.5 in., t-tw-0.375 in. and d=3 in. (a) If the bending stress at point K is 2720 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o at point H (positive if tension, negative if compression). H K Answers: (a) M₂= i (b) oH = i tw lb-ft. psi.
What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 17 mm and a shear force V = 29 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa.
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
A prismatic bar with shear modulus G is subjected to an axial torque T. It has an elliptical cross-section with an elliptical hole as shown. (a) Choose a suitable Prandtl stress function (x, y). (b) Find the magnitude of the shear stresses at A, B, C, and D. (c) Find the torsional constant J for the cross-section. y A 2а a За/2 -За-
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
If the beam is subjected to an internal moment of M=30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. V Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm 150 mm M 15 mm