The voltage of an ac source is given by V(t)= Vo sin wt, where Vo= 100 V and w = 180 rad/s. Calculate the average power output of the source if it is connected across (a) a 35-μF capacitor, (b) a 45- mH inductor, and (c) a 60-02 resistor. (d) What is the rms voltage of the ac source? Hint a. The average power output with the capacitor is b. The average power output with the inductor is c. The average power output with the resistor is d. The rms voltage of the ac source is inction Molnt 5 Morrago instructor W. W. W. V. Additional Hints

The voltage of an ac source is given by V(t)= Vo sin wt, where Vo= 100 V and w = 180 rad/s. Calculate the average power output of the source if it is connected across (a) a 35-μF capacitor, (b) a 45- mH inductor, and (c) a 60-02 resistor. (d) What is the rms voltage of the ac source? Hint a. The average power output with the capacitor is b. The average power output with the inductor is c. The average power output with the resistor is d. The rms voltage of the ac source is inction Molnt 5 Morrago instructor W. W. W. V. Additional Hints

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The rms current in a 33.0-0 resistor connected to an AC source is 2.80 A. (a) What is the rms voltage across this resistor? V (b) What is the peak voltage of the AC source? V (c) What is the average power dissipated by the resistor? W (d) What is the maximum current across this resistor? A
Two ac generators supply the same voltage. However, the first generator has a frequency of 1.2 kHz, and the second has a frequency of 5.7 kHz. When an inductor is connected across the terminals of the first generator, the current delivered is 0.15 A. How much current is delivered when this inductor is connected across the terminals of the second generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. Number i Units 1₂ L 0000 V sin 2π f₁t Circuit 1 12 L 0000 Vo sin 2x f₂t Circuit 2
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
A wire is carrying a direct current of 20 A and a sinusoidal alternating current of peak value 20 A. Find the rms value of the resultant current in the wire.
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
5. An impedance draws a current i(t) = 10sin(wt-30°) ampere from a voltage v(t) = 220cos(@t-65°) volts. Determine: a. The current in polar form (peak) b. The voltage in polar form (peak) C. The current in polar form (RMS) d. The voltage in polar form (RMS) e. The impedance
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........