There are 5 wires (circled numbers) used to implement the following logic circuit. There is a fault in wire-3. The fault in the wire-3 is always producing logic 1 (stuck at 1 indicated by s-a-1) irrespective of input z . What is the Boolean expression for output ƒ of the faulty circuit? х. De s-a-1 (a) ƒ = xz + yz (b) ƒ =x+y (c) ƒ =1 (d) ƒ =0

There are 5 wires (circled numbers) used to implement the following logic circuit. There is a fault in wire-3. The fault in the wire-3 is always producing logic 1 (stuck at 1 indicated by s-a-1) irrespective of input z . What is the Boolean expression for output ƒ of the faulty circuit? х. De s-a-1 (a) ƒ = xz + yz (b) ƒ =x+y (c) ƒ =1 (d) ƒ =0

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter9: Components For Electric Motors

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

P3/ A sinusodail signal Shown in figure (1) be low: Time (t) Upp is 12v and T= 0,08 Sec I- Explain in details the method of Converting the above signal to a digited bits stream start with 0ooo upto 1111 I1- what is the bit reate for the process abuve ? I71- ealeulate: Signel Signl to noi se ratio and noise power.
What will be the modified form of the following codeword is odd parity scheme is used: Codeword: 0110101
3/ A Smufodail signal shown in figure (1) be low: Time (t) VPPニRY Upp is 12v and T= 0.08 Sec I- Explain in details the method of Converting the above signal to a start with otsitel bits stream 0oo0 upto 1111 I1- what is the bit reate for the process a buve ? I7l- ealeulate: Signel Signl to noi se ratio and noise power .
What will be the final value of DI after executing the following piece of code? Execute the instructions dependently one after another. CLD MOU CX,OFOH MOU AX,05678H MOU DI,01000H MOU ES, DI SUB DI, DI REPNZ SCASB -R AX-0000 DS-073F 073F:0100 0000 D 1000:0 F 1000:0000 92 00 14 12 54 56 44 78-AD 56 78 FO 00 00 00 00 BX-0000 CX-0000 DX-0000 SP-00FD ES-1000 SS%3073F CS=073F BP-0000 SI=0000 DI=0000 IP-0100 NU UP EI PL NZ NA PO NC ADD IBX SI1,AL DS:0000 CD TUDX.Ux..... .... Notes: 1- Use the DEBUG window to answer this question (values shown are prior to execution and in hexadecimal 2- Write down the final value of DI as four hexadecimal digits without any additional characters.
Question No. 5 Perform following operations i. (11100011)2- (10101010)2 ii. 789 + 234 → (BCD Addition)
An 8X1 multiplexer has inputs A, B, and C connected to the selection inputs s2, s1 and s0, respectively. The data inputs, I0 through I7 are as follows: I1=I2=I7=0 I3=I5=1 I0=I4=D I6= D’ Determine the Boolean function that the multiplexer implements
AND OPERATIONS can you please answer Table I?
processors Systems And Interfacing If you subtract two decimal numbers, after BCD subtraction, to correct the result we use Oa AAA Instruction Ob AAM instruction Oc DAA instruction Od. DAS instruction Next page Windows bu alacy Jait ------ hp f3 ア D f7 19 %23 & フ R T Y Y ! VACO 12 DI F 1 G Y BY N T こo つ

There are 5 wires (circled numbers) used to implement the following logic circuit. There fault in wire-3. The fault in the wire-3 is always producing logic 1 (stuck at 1 indicated by s irespective of input z. What is the Boolean expression for output f of the faulty circuit? Ta y. De s-a-1 (a) f=xz+ yz (b) f x+y (c) f=1 (d) f=0 Answer OA
4. Write a Boolean expreision for the following statement Fisa I" if A, B&C are all I's or if only two of the variable is a0
C1. The figure below shows the state diagram of a synchronous circuit to detect the sequence 101. The circuit has a single input X, and a single output Z. Answer the following questions: c) Draw and fill the state table. d) Write the Boolean equations of the state variables and the output Z. so S1 S2 S3
Hello. I keep getting lost on my process and keep getting wrong answers. I'm having trouble getting the q points and I'm possibly getting the polarity wrong in my equations. How would you go about this? Thank you for your time and help. I know it is a lot so if you could just do the first couple so I can see what is going on, I'ld appreciate it very much.