This question relates to the static and dynamic balance of an unbalanced shaft that is supported by bearings at its two ends, as shown in Figure Q4. The shaft rotates at 300 rev/min and the out-of-balance loads are given below. m1(kg) = 1.6 m2(kg) =2.4 m3 = 2 kg Z 4 X 43 0 Figure Q4 0₁ 0₂ 03 30° 120° 315° r1(m)= 0.7 r2(m)=0.5 r3(m)= 0.6 11(m)=1.4 12(m)= 2.0 13(m)=2.5 a) Using the data provided in Table Q4, take moments about the left-hand end of the shaft and so construct the mrl diagram for the system. Calculate the angular position and the mass of material needed to close the mrl diagram, if the mass is to be added at a point 1.7 m from the left-hand end of the shaft at a radius b) Construct the mr diagram the left-hand end of the shaft at a radius of 1 m to close the mr diagram and so balance the forces acting on the shaft.

This question relates to the static and dynamic balance of an unbalanced shaft that is supported by bearings at its two ends, as shown in Figure Q4. The shaft rotates at 300 rev/min and the out-of-balance loads are given below. m1(kg) = 1.6 m2(kg) =2.4 m3 = 2 kg Z 4 X 43 0 Figure Q4 0₁ 0₂ 03 30° 120° 315° r1(m)= 0.7 r2(m)=0.5 r3(m)= 0.6 11(m)=1.4 12(m)= 2.0 13(m)=2.5 a) Using the data provided in Table Q4, take moments about the left-hand end of the shaft and so construct the mrl diagram for the system. Calculate the angular position and the mass of material needed to close the mrl diagram, if the mass is to be added at a point 1.7 m from the left-hand end of the shaft at a radius b) Construct the mr diagram the left-hand end of the shaft at a radius of 1 m to close the mr diagram and so balance the forces acting on the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed of the wagon wheels is n = 37 rpm. The total radial load carried by the wagon is given as Fr= 16060 Newtons. In addition, due to road conditions, Fa axial load is applied to the wagon. If the axial load on the A bearing is 10% of the radial (vertical) load on this bearing, calculate the dynamic load number (C) of the bearing in the A bearing in Newtons for 18616 hours of life. fo*Fa/Co = 0.345 Pi=3.14
The figure shows the rear rotating axle of a 4-wheel wagon with the same FRONT AXLE design and REAR AXLE design. The wagon moves at a constant speed and the diameter of the wheels carrying the axle is D=512 mm and the circumferential speed=3.1 m/s. Due to the load (m) on the wagon, a force of 16574 Newtons acts in the vertical direction. ALSO, a horizontal force of 21% of the vertical load acts on the wagon laterally (horizontally) in bends. It is planned that the bearings of the axle will be bearing 6008 deep groove ball bearings. Calculate the life of bearing A in hours.The radial effect of lateral loads will not be taken into account in the bearing force calculation. Fo.Fa/Co = 1.38 Pi=3.14
Find the value of the input torque on the crank-shaft mechanism in following Figure. The centers of gravity of link 2, 3 and 4 are at G₂, G3 and G4 respectively. The masses and moments of inertia of the links are: m₂=2 kg, m3 =0.5 kg, m4 = 0.5 kg, IG2 = 0.001 kg m², IG3 = 0.01 kg m² and IG4 = 0.002 kg m². It is known that: O₂A = 3 cm, AB = 7 cm, AG3 = 2 cm, 0₂ = 60°, @₂=-20 rad/s², a₂ = -100 rad/s² and that external force P4 has a magnitude of 98 N. consider 03 =338.2° and the following accelerations for links 3 and 4: a3 = -250.26^i- 849:45^j cm/ s², α3 = A3 174:44 rad/ s², aG4 = -25.45^i cm/s², a4 = 0. A 2 Mo 0 10₂=G₂ G₂ 3 B=G4 P₁
A shaft is supported by two bearings placed1.2 m apart. A pulley of diameter Dc=0. 675 meter is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25 kN. Another pulley of diameter Dd= 0.575 meteris placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt, which is placed horizontally to the right. The angle of contact for both the pulleys is 180° and u = 0.24. Determine the suitable diameter for a solid shaft, allowing working stress of 63 MPa in tension and 42 MPa in shearfor the material of shaft. Assume that the torque on one pulley is equal to that on the other pulley C A De m B Da m 0.3 m 0.2 m 1.2 m.
4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180 , and ? = 180? and ? = 360? respectively. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed.
A conveyor is used to drive the inertial load of 0.02 kg m² in the required speed range with a brushless DC motor and a gearhead having reduction ratio of 15:1 as shown in the figure below. The belt speed is V=1 m/s and the roller diameter is D=0.1 m. Choose the correct statement. Load Motor Right Angle Gearhead O The moment of inertia of the load referred to the motor shaft is 0.00133 kg m² O The moment of inertia of the load referred to the motor shaft is 0.0133 kg m² O The rotation speed of the motor shaft is 1665 RPM O The rotation speed of the gear shaft is 100 RPM O The rotation speed of the motor shaft is 2865 RPM.
A certain system like that shown in the figure has a load inertia = 102 kg-m2, a shaft inertia of Is=6 x 104 kg-m2, and a motor inertia of Im 2 x 103 kg m. A friction torque of 1.5 N-m acts on the load. It is desired to rotate the load through two revolutions (4 rad) in one-half second from start to stop. The load should be rotated at a constant speed for 0.6 s during the slew phase. uired torgue, and the rms average torque.
Om A1 DOF revolute joint robot is actuated by a motor through a gear having a gear ratio, 7 : 5 as shown in the figure below (where Jm is the motor inertia and Ji is the link inertia. The kinetic energy is given by O Save J, O. m 2 m 2 Jm0 m + 50 m 25.J, m т m O None of the above
Five (5) uniform discs of mass 5 kg each are fitted onto a shaft which is rotating at 3,000 rpm constantly and supported by two (2) bearings P and Q as shown in Figure Q1. The system is initially totally balanced. If a few modifications are carried out as following:- Disc B: Removal of 0.2 kg at radius 0.01 m and position 240° Disc D: Addition of 0.1 kg at radius 0.02 m and position 150° Calculate the following:- The dynamic force acting on bearings P and Q. The mass mc and mg to be added at disks C and E respectively to be positioned at radius 0.02 m, and their respective angles to balance the system. а. b. 0.1 m 0.1 m 0.1 m 0.1 m 0.1 m 0.1 m 90° 180° 0° P 270° A C D E Figure Q1 -図図。
Figure (1) depicts a four-throw crankshaft that has the following properties: mi = m2 = m3 = m4 10 kg and r = r2 = 13 = r4 = 40 mm. Determine the balancing arrangement in correction planes P and Q. 90 O = C min 100 mm 100 mm 100 mm 50 mm
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.