Three impedances Z1, Z2 and ZL are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and ZL. Calculate the maximum power transferred to load impedance ZL . Use Maximum power transfer theorem.

Three impedances Z1, Z2 and ZL are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and ZL. Calculate the maximum power transferred to load impedance ZL . Use Maximum power transfer theorem.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Mesh analysis
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
use kirchhoffs Junction rule and loop rule to solve for currents I1 , I2 and I3..
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.
6. The figure below shows a single-line-diagram of part of a power system. For each transformer in the diagram state a suitable connection method, giving reasons for your suggested connection method. G1 G1 800MW 200MW 15kV 10kV T1-T4 88 T5-T6 250MVA each 125MVA each 330/15kV 88/10kV Line 1 Line 2 T7-T8 100MVA each 330/88kV T9 T10-T11 50MVA 50MVA each 88/66kV 88/11kV T12 2MVA 11/0.4kV Singe-phase loads
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected inseries with the supply voltage V1 while the impedance Z2 is connected in series with the voltageV2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angleof 15° ohms, calculate the currrent flowing in each impedance. Use Superposition theorem.
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected inseries with the supply voltage V1 while the impedance Z2 is connected in series with the voltageV2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angleof 15° ohms, calculate the currrent flowing in each impedance. Use Nodal analysis.
If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many single-phase transformers are needed? Explain.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --