Throw some light on how DC machines are classified based on excitation? Suppose a separately excited DC generator has an armature resistance of 0.12N and negligible armature inductance. At rated field current and rated rotor speed, its open-circuit voltage is 200 V. When this generator is operated at half the rated speed, with half the rated field current, an un-charged 1000 uF capacitor is suddenly connected across the armature terminals. Assume that the speed remains unchanged during the transient. At what time (in microsecond) after the capacitor is connected will the voltage across it reach 25. Explain in detail?

Throw some light on how DC machines are classified based on excitation? Suppose a separately excited DC generator has an armature resistance of 0.12N and negligible armature inductance. At rated field current and rated rotor speed, its open-circuit voltage is 200 V. When this generator is operated at half the rated speed, with half the rated field current, an un-charged 1000 uF capacitor is suddenly connected across the armature terminals. Assume that the speed remains unchanged during the transient. At what time (in microsecond) after the capacitor is connected will the voltage across it reach 25. Explain in detail?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2) In DC machine, the speed is 800 RPM, the flux per pole is 2 m wb, and it has a Lap winding armature with 6 coils (4 turns conductor per coil) . The DC machine has 2 poles and armature draws lc= 5.5 A. If the winding redesigned as wave winding, find the EA , Tem and Pem and explain what will happen when we change the design from lap to wave winding connection.
What will be the front and back pitches of the 6-pole dc generator with a simplex 2-layer wave winding having 36 conductors and the winding is retrogressive?
A seperately excited DC generator has a no load voltage of 127 V, Ra= 0.02 ohm and Rsh=15 ohm. Find the armature current when the generator terminal voltage is 120 V on load.
Between a separately-excited and a self-excited DC generator, which is simpler to construct and why?
A lap-winding DC machine has 24 coils, 18 turns per coil, and 4 poles. The average flux density per pole is 1T. The effective length is 40 cm and the armature radius is 10 cm. The armature velocity is 140.2 rad/sec and the armature current is 24 A. The average flux per pole in Wb is: 6.283 0.06283 O 0.6283 0.006283
i. Briefly describe the 5 major types of DC generators according to the manner in which their field flux is produced.
For a 4-pole dc armature with 28 slots and 8 coil-sides per slot, find the winding pitches and the commutator pitch for a wave winding. What is the distance between brushes in terms of commutator segments?
Write an article describing the DC Generator. Provide applications of DC generator. Provide the importance of a DC generator
3. What are the various losses in an induction motor? On whatfactors do they depend?
An 8-pole dc generator with 778 wave connected armature conductors and running at 500 rpm supplies a load of 12.5 ohms resistance at a terminal voltage of 50V. The Ra = 0.24 ohm and Rsh = 250 ohms. Find the flux per pole.
no more thank 50 words. In the load characteristics of a separately-excited DC generator, its output voltage decreases with increasing load current (decreasing load resistance). What possible fix or action can you take to offset this decrease in voltage and maintain the output voltage at a constant level as the load current increases?
The following figure shows a simplified endivi and inductor for a dc motor. The inductor has an average magnetic path length of 50 cm and a cross-sectional area of 12 cm2. The mean path length of the endivi is 5 cm and the cross-sectional area is given as 12 cm2. The air gap between the armature and the inductor is 0.05 cm, and the cross-sectional area of each air gap (including fringe effect) is 14 cm2. The magnetic permeability of the iron of the core is µr =2000 H/m and 200 turns are wound on the core. If the current through the conductor is set to be 1 A,a) What is the mmm force of the magnetic circuit?b) What is the reluctance of the inductor and armature?c) What is the magnetic flux density in the air gap?Is it Tesla?d) Calculate the inductance of the winding.e) If 10 turns of bandage are wrapped around the armature under these conditions,What is the torque to be induced if current A is passed?