To Tc B A If TB=3T and TC=1T, determine the maximum value of T considering that the maximum torsional shearing stress is 85MPA for Bronze and 100MPa for Steel and that the limiting angle of twist for AC is 8. АВ BC Bronze Steel Material 1 2 Length, m 90 60 Diameter, mm 83 Shear Modulus, GPa 35 solid solid Type of Shaft

To Tc B A If TB=3T and TC=1T, determine the maximum value of T considering that the maximum torsional shearing stress is 85MPA for Bronze and 100MPa for Steel and that the limiting angle of twist for AC is 8. АВ BC Bronze Steel Material 1 2 Length, m 90 60 Diameter, mm 83 Shear Modulus, GPa 35 solid solid Type of Shaft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A drive shaft running at 2500 rpm has outer diameter of 60mm and innerdiameter of 40mm. The allowable shear stress in the shaft is 35MPa. Determine themaximum power that can be applied. Present drawings/FBD’s illustrating your solution.
Problem 2: F = 10 kip -10 in- -5 in- -5 in- d/5 R. R1 d/ 10 R. 1.4 d- R2 I in The shaft shown above rotates at 1200 RPM and supports a 10 kip load. The material of the shaft is 1095 hot-rolled steel and its surface is machined and then polished. Using a factor of safety of 1.6, specify the minimum value of diameter d for a life of 1,000 hours.
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.
Q1 The rotating solid steel shaft is simply supported by bearings A and B, the gear has 500-mm pitch diameter. The shaft transmits a torque, T. The shaft is machined from steel AISI 1040 CD. Using a factor of safety of 2.5, determine a- The torque T b- Reactions RA and Rc c- Draw th Bending Diagram d- Maximum bending moment e- the minimum allowable diameter of the shaft using DE_Goodman theory. Assume sharp fillet radii at the bearing shoulders. 450 mm B A 500-mm dia. Fy = 8000 N 550 mm 00 C De
Q1 The rotating solid steel shaft is simply supported by bearings A and B, the gear has 500-mm pitch diameter. The shaft transmits a torque, T. The shaft is machined from steel AISI 1040 CD. Using a factor of safety of 2.5, determine a- The torque T b- Reactions RA and Rc c- Draw th Bending Diagram d- Maximum bending moment e- the minimum allowable diameter of the shaft using DE_Goodman theory. Assume sharp fillet radii at the bearing shoulders. 450 mm B 550 mm C 500-mm dia. Fy = 8000 N
A hollow shaft made from AISI 4340 steel has an outer diameter D. of 4 in. and an inner diameter Di of 2.5 in. The shaft rotates at 46 rpm for one hour each day. It is supported by two bearings and loaded in the middle with a load W of 5500 lbf. The distance between the bearings Lis 78 in. The maximum tensile stress due to bending for this type of cyclic loading is calculated using the following equation: 8WLD, #(Dg – D{) What is the stress ratio for this type of cyclic loading? Would this shaft last for one year assuming a safety factor of 2?
EHide blocks Lets consider a solid circuiar shalt subjected to the torque loads as shown. Determine the minimum required diameter "Dif the shaft is made of a material having a shear modulus G 50 GPa, so that the maximum angle of twist at its end will not exceed -0.35° (calculated according to the positive sign convention). 100 N.m 500 N.m 200 N.m 300 mm 600 mm 600 mm Select one: O 40 mm O 70 mm O 80 mm O 60 mm O 50 mm
Q-3 A 25-mm-diameter solid round bar has a groove 2.5-mm deep with a 2.5-mm radius machined into it. The bar is made of AISI 1050 CD steel and is subjected to a purely reversing torque of 250 N-m. For the S-N curve of this material, let f= 0.9.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3 in a 6 m length when subjected to a torque of 12 kN-m? (b) what maximum stress is developed in the shaft? Use G-83 GPa. Remember the angle of twist (0) calculated using the equations is in radians. Incorrect solution will be downvoted
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you