Two coils have a mutual inductance of 480mH. One coil is supplied with a current given by I(t) = 3t2 – 2t – 6, where I(t) is in amperes and t in seconds. What is the induced EMF in the other coil at t=3.5s? %3D

Two coils have a mutual inductance of 480mH. One coil is supplied with a current given by I(t) = 3t2 – 2t – 6, where I(t) is in amperes and t in seconds. What is the induced EMF in the other coil at t=3.5s? %3D

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Related questions

Q: Two geometrically similar pumps are running at the same speed of 1000r.p.m. One has an impeller diam...

A: Given Pump No.1:Speed N1=1000 rpmDiameter D1=0.4 mDischarge Q1=30 l/s=0.03 m3/sHead H1=20 mPump No....

Q: Ipss= 10 mA Vp=-4 V 4.7 kl 10 Vo ww0-2.5 V 2 MO FIG. 8.72 Problem 19.

Q: List out the various types of pressure sensor. Explain any o

Q: Consider a voltage source v(t) = 220 cos (100nt - 30°) Define a. The amplitude of v(t) b. The angula...

Q: Prob#4 Find I, by nodal analysis. 23222° A -j4 Q 10 10215° V 1Ω + 31, 5V, 10 V,33N

A: Nodal analysis is a method to analyze a complex circuit using Kirchoff’s current law to find the vol...

Q: 1) a) For the circuit shown , let R= 1kohm, L1 = 10mH, C1= 5nF. Calculate the values of Z, Phase Shi...

A: The solution is given

Q: From the given circuit diagram, what is the value of diode current? 1k R1 D2 Si- 8V+ D1 Ge O 7.3 mA ...

A: Silicon diode cut in voltage is 0.7 volts Germanium diode cut in voltage is 0.3 volts

Q: From the circuit below, determine the current IRS flowing through the resistor RS.

Q: 4-12. Draw the f-i analogous mechanical system for the electrical circuit of Fig. 4-33.

Q: Answer the problem below on your templated paper. Show your complete solution. 40/60° V V1 4Ω V2 ww ...

Q: Solve the differential equation mä(t) + cx(t) + kx(t) = kf (t) By means of a Fourier analysis, where...

A: Given the differential equation as given below : mx¨(t)+cx˙(t)+kx(t)=kf(t) By means of a Fourier ana...

Q: 2. Compare the performance of the transmission line (regulation, efficiency) with pure resistive loa...

Q: Which of the following is equal to Boolean function given by following expression? F(A, B) -Σm0, m3)...

A: Given data, FA,B=∑m0, m3

Q: Si transistor; B=50 Determine: g) dc transistor terminal voltages h) hie i) Rin

A: Brief description : In the above given question they have mentioned a common collector amplifier cir...

Q: design a combinational circuit that accepts a 2-bit integer as input and generates a 4-bit integer a...

Q: What is the maximum period obtainable from the following generator? Xn+1 = (aXn) mod 24 What should ...

Q: An 8-bit word is sent (bit-by bit) over a digital link with bit inversion probability q 0.1, The pro...

Q: 2 A( [3 A i -5 A -3 A

Q: What do we call the minimum energy that is required by an electron to leave the metal target in the ...

A: The minimum energy that is required by an electron to leave the metal target in the photoelectric ef...

Q: What are some of the significant rules used by technicians who want to follow the smart money and wh...

A: The technician's responsibilities include monitoring and servicing systems, diagnosing problems and ...

Q: R1 RNSID 2 55 µF Vs 6 VRMS 80 Hz L1 50 mH

A: The solution is given below

Q: Given the following DT LTI system: y/n] – y/n – 1] – 2y[n – 2) = ¤[n] + 2r[n – 2]| y[–1] = 4, y[–2] ...

Q: A 500 KVA,3.3 KV,50 Hz,600 rpm,3 phase salient pole alternator has 180 turns/phase. Calculate the le...

Q: Current density is given in cylindrical coordinates as J = -106z1.5azA/m2 in the %3D region 0sps 20µ...

A: Given vector current density,J=-106z1.5 az A/m2 for 0⩽ρ⩽20 μmAlso, J=0 for ρ⩾20 μm

Q: Find feedback ratio, feedback factor, voltage gain without feedback and voltage gain with feedback f...

A: Given the circuit as shown below: We need to find the feedback ratio,feedback factor,voltage gain w...

Q: What is the ripple factor of a DC signal having ripple voltage of 2 V and a DC voltage of 50 V? Answ...

Q: From the below op-amp design, the maximum Vout equals +10 R1 V1 U1 7Vrms 60HZ 10ka Vout R3 V2 7Vrms ...

Q: find Q-pant values and Iccsae) NeG(uetoff) Sketch Dc load Line, indi cat the velubts sketch tihe on

Q: From the circuit shown below, what is the value of Vo? 12 V Si LED White (vth = 4V) 4.7 k2 O 7.3V O ...

Q: or the circuit shown, Determine the following: (a) hie (b) Av (c) Ai (d) (p-p) if Rs connected is 1K...

Q: the Current I equal in network

Q: + vp - si to 12V

Q: Find the pull on the plunger of an electromagnet when the total flux uniformly distributed is 0.8 mW...

Q: For an inverting amplifier circuit, calculate the O/P voltage and draw both I/P and O/P voltages if ...

Q: R1, R2, and R3, have values of 85 ohms, 69 ohms, and 25 ohms. What is the equivalent resistance acro...

Q: For the given system transfer function below, find the value of the rise time. 10 G(s) = a+4.4

Q: 2) a) For the circuit below, what is the charge on each of the capacitors once steady state conditio...

A: a) The circuit is shown below: The charge on the 2uF capacitor is, C1=2μFV=120 VoltsQ1=C1VQ1=2×10...

Q: 1. Derive the formula for the RMS value for the following a) b)

A: 1. a) eo=ep sint ;0⩽t⩽π-ep sint ;π⩽t⩽2πTime period T=2πRMS value eRMS=1T∫0Teo2dteRMS2=12π∫0πepsinωt...

Q: Find VCB?

Q: What is the minimum sampling rate needed in order to successfully capture frequencies up to 80MHz in...

A: Control systems are represented by transfer function. This can be written in both time domain and s...

Q: a I1 620°A 212 Y.079 I3 -j12 b 12 I4 j20 V.07 I2 I5 e

Q: Which of the following is the Laplace transform of the time-domain signal z(t) = e"u(-t)? %3D Ο Α. X...

Q: Determine the values of the node voltages at nodes a, b, C, and d of the circuit shown. Hint: Notice...

Q: 2. Determine the line currents for the three-phase circuit shown below. Let V, = 11040°, V½ = 110 - ...

A: In this question, 3 phase balanced star connected source is supplied to the unbalanced load. We ne...

Q: Determine I,max for the shown network below if vi = 14Vdc Imax Si 4.7 k2 68 kQ Vi Si O 2.05mA O 1.49...

Q: Consider A = (1, 2, 2) and B = (0,– 1,3). %D Determine: a)the angle between vectors A and B b)proj A...

Q: Supply the signal generator and adjust the output to a sinusoidal voltage of 8V peak to peak – 500HZ...

Q: 1. Determine V1 in the circuit shown below. Vx + 10 kN 5 kN Vx 25 V V1 4

A: Given circuit,

Q: A 5-Ohm resistor is in parallel with a 20-Ohm resistor, is supplied by a 4-A current source. Calcula...

Q: 6.18 Find Ceq in the circuit of Fig. 6.52 if all capacitors are 4 µF. Cea Figure 6.52

Question

Q 1. Two coils have a mutual inductance of 480mH. One coil is supplied with a current given by
I(t) = 3t2 – 2t – 6, where I(t) is in amperes and t in seconds. What is the induced EMF in the
other coil at t=3.5s?
-
[10]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
If i have a coil with an inductance 0.14 H and a resistance of 12ohm is connected across a 110V , 25Hz source. how would you make the current in the coil and the phase between the cirrent and supply voltage ?
(a) 13. A coil with 60 turns wound over a ferromagnetic core having relative permeability 400 has an inductance of 50 mH. If coil turns are doubled and the core is replaced by a new ferromagnetic core having relative permeability 600, the new inductance would be (a) 0.03 H (b) 0.3 H (c) 3 H altarnator will reverse if (d) 0.15 H
A coil has a resistance of 75 ohms and an inductance of 1.4H. When the applied voltage is 240V, at what frequency is the current 0.3A? 87.67Hz 93.25Hz 92.34Hz 90.55Hz
A 2amp current flows through series connection of inductance L1 = 3H and L2 = 6H. If the coils are additively coupled and the value of M is 2H, then the stored energy will be ?
From a coil with an inductance of 2 mH, i = 5(1-e -5000t) Ampere current is passing. At the ends of the coil.Calculate the voltage and the energy stored in the coil.
Due to mutual inductance between two coils, there is an induced emf in one coil due to a change in current in the other coil. O True O False O Hard to say
What is the value of the induced voltage of the self-inductance when the rate of current is from 200 uA to 20 uA and the total time interval is 5 uS?
For the series RL circuit shown in the figure below, answer the following questions and justify your answer.If the current is kept constant, does the coil have inductance?If the current is kept constant, does the coil affect the current value?Can the reverse emf ever be greater than the battery emf?
C) A 25 A electrodynamic ammeter is controlled by a spring having a constant of 5.7295x 10-6 Nm/rad. The full scale deflection is 110°. Determine the inductance of the instrument while measuring a current of 20 A. The mutual inductance at 0° deflection is 4 u H and the change in mutual inductance is linear with the deflection.
The inductive reactance of a 0.06-H coil connected to a 120-V, 60-Hz source is?