Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in³ Cyl. A DR = 62 in³ Cyl. B DE 44 in³ Cyl. B DR = 41 in³

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in³ Cyl. A DR = 62 in³ Cyl. B DE 44 in³ Cyl. B DR = 41 in³

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.6: Cnc Milling: Programming

Problem 8RQ: Briefly describe the use of I and J for the arc center method of circular interpolation.

See similar textbooks

Similar questions

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3
Direction: •Show unit cancellations and do not use shift solve.•Show your complete solution with this format: Given, Required, Solution. •Use 4 decimal place for answers. Question: A 6-stage-double-suction cetrifugal pump discharges 71 kg/s of oil (SG=0.75) at 1750 rpm with pressure drop of 525 psi. Find the specific speed in rpm. Subject: Fluid MachineriesCourse: Mechanical Engineering
refer to the table below. Apply interpolation if necessary
Briefly describe the use of I and J for the arc center method of circular interpolation.
Provide an FBD in this given problem
Draw the block diagram of a Displacement measurement system .Also identify the names of the functional elements used in the measurement system.
Kindly graph the vector and acceleration
Direction: •Show unit cancellations and do not use shift solve.•Show your complete solution with this format: Given, Required, Solution. •Use 4 decimal place for answers. Question: A centrifugal pump delivers 300,000 liters per hour of water to a pressurized tank whose pressure is 5850 psf. The source of water is 5 meters below the pump. The diameter of the suction pipe is 300 mm and the discharge pipe is 250 mm. Calculate the kW rating of the driving motor assuming the pump efficiency to be 72%. Subject: Fluid MachineriesCourse: Mechanical Engineering
A tachometer has an analog display dial graduated in 5‐revolutions‐per‐minute (rpm)increments. The user manual states an accuracy of 1% of reading. Estimate the design‐stageuncertainty in the reading at 50, 500, and 5,000 rpm.
I need the answer quickly Orthographic projection of the component show below
How u find the correction factor 0.95 plz I need excellent explanation make the table and pic and explain and select and show me plz
Please veryyy urgent with counting the numbers on graph and explain how to count j2 pls