Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolt are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80N/mm2.

Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolt are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80N/mm2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.13P: A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of...

See similar textbooks

Similar questions

The halves of the coupling are held together by four 5/8-in.-diameter bolts. The working stresses are 12 ksi for shear in the bolts and 15 ksi for bearing in the coupling. Find the largest torque T that can be safely transmitted by the coupling. Assume that the forces in the bolts have equal magnitudes. 0.5 in. 3.5 in.
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350
10/.. find the shear stress in bolts 2 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM LO -O- O 300 mm 8 mm
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
The copper pipe has an outer diameter of 2.5 in. and an inner diameter of 2.25 in. It is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown.(Figure 1) Points A and B lie on the pipe's outer surface. Figure C B |--M 2 ft V 150 lb-ft/ft. TIM A 2 ft V -- < 1 of 1 Determine the shear stress at point A. Express your answer to three significant figures and include appropriate units. TA = ΤΑ Submit Part B O — μA 4 TB = Value Units Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining μA P Determine the shear stress at point B. Express your answer to three significant figures and include appropriate units. Value Units ? www ? Submit Previous Answers Request Answer
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
The solid shaft of radius r is subjected to a torque T. Determine the radius r of the inner core of the shaft that resists one-half of the applied torque (T>2). Solve the problem two ways: (a) by using the torsion formula, (b) by finding the resultant of the shear-stress distribution.
A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of the shaft if the maximum shear stress is 50 .
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm