Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The assembly is pulled in tension by a force P. P=100 kN. Find: a) The stress in each Steel Rod. b) The stress in the Aluminum Rod. Steel Rod Area = .5 m² Aluminum Rod Area = .5 m² P P Steel Rod Area = .5 m² Rigid Cover Plates

Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The assembly is pulled in tension by a force P. P=100 kN. Find: a) The stress in each Steel Rod. b) The stress in the Aluminum Rod. Steel Rod Area = .5 m² Aluminum Rod Area = .5 m² P P Steel Rod Area = .5 m² Rigid Cover Plates

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Repeat the previous problem using sx= 12 MPa.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.