4(a)What do you think is the primary requirement for Delta Modulation?(b) If we increase the step size in a PCM system, what is the effect on (SNR)q?For a 7 bit PCM system with input as a fully loaded sinusoidal signal what will be the(c)(SNR), in dB?If the maximum frequency of a baseband signal is 4KHZ, which is the input to an 8-bitPCM, what should be the channel bandwidth for a distortion less transmission?Why is a delay block required in the transmitter and receiver system of a DM?(e)

A) for delta modulation 1 bit quantizer is needed

uraw ne yscm UIOCK UlagTam. 4 (a) What do you think is the primary requirement for Delta Modulation? (b) If we increase the step size in a PCM system, what is the effect on (SNR)q? For a 7 bit PCM system with input as a fully loaded sinusoidal signal what will be the (c) (SNR)q in dB? If the maximum frequency of a baseband signal is 4KHZ, which is the input to an 8-bit (d) PCM, what should be the channel bandwidth for a distortion less transmission? (e) Why is a delay block required in the transmitter and receiver system of a DM? (e)

uraw ne yscm UIOCK UlagTam. 4 (a) What do you think is the primary requirement for Delta Modulation? (b) If we increase the step size in a PCM system, what is the effect on (SNR)q? For a 7 bit PCM system with input as a fully loaded sinusoidal signal what will be the (c) (SNR)q in dB? If the maximum frequency of a baseband signal is 4KHZ, which is the input to an 8-bit (d) PCM, what should be the channel bandwidth for a distortion less transmission? (e) Why is a delay block required in the transmitter and receiver system of a DM? (e)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3] Let m(t) be a baseband signal whose spectrum is described in the figure below. This signal is sampled at the rates (a) 16kHz, (b) 25% over the Nyquist rate. DraW the spectrum of the sampled signal in each case. Mf) (Hz) 3k 0 3k 7.5k -7.5k
A television signal (video and audio) has a bandwidth of 4.2MHZ. This signal is sampled, quantized and binary coded to obtain a PCM signal. (a) Determine the sampling rate if the signal is to be sampled at a rate 20% above the Nyquist rate. (b) If the samples are quantized into 1024 levels, determine the number of binary pulses required to encode each sample. (c) Determine the binary pulses rate(bits per second) of the binary-coded signal
B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) The waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 12
An analog signal, with an absolute bandwidth of 10 KHz, is to be converted to a digital signal usingan A/D converter and stored in a PC. If the quantization error must be within ±0.05% of the peak-to-peakvalue of the analog signal, determine the storage requirement. Please assume that we are going to record 8seconds of data, sampled at 1.5 times the Nyquist rate.
1. Write an equation for an AM-modulated signal (AM-DSB), and explain the significance of all constants in the equation. Present a Simulink-style block diagram to implement an AM modulator.
D. Use the small signal circuit to find the expression for Vo/Vin. Consider the Body Effect of Mi but, neglect the channel length modulation. Voo WWD M₁ V₂
zain IQ AM Modulatio... -> AM Modulation 1. What is the main feature in AM modulation, that is used to judge if the modulation is good or not? Explain with examples. 2. Can AM modulated signal change phase and/or frequency? Explain the reason. 3. What is modulation index? Its formula? 4. Plot an AM modulated signal, that has an information signal m(t) = 10 sin(10nt) and a carrier signal c(t) = 15 cos(1000t). Calculate the modulation index (u). Is it a good modulation? If no, suggest a change in one of the signals above and calculate u again, so that it approaches ideal case. 5. Draw the modulation block diagram of AM. ...
When the JFET is cutoff, this mean that: Select one: a. The channel is completely closed by the depletion region b. The channel isr everse-biased C. The channel is extremely narrow d. The channel is at its widest point
1. The evaluation of 8(t - 1)8(t - 2)dt is 2. A sinusoidal modulated signal has its Atmax =50 and the minimum is half of it, so the efficiency of modulation will be.. .........
After getting the formula of FM and PM moducation signal, how can I sketch this one.
A compact disc (CD) records audio signals digitally by using Pulse Code Modulation (PCM). Assume the audio signal bandwidth to be f, kHz (as in table Q4) and if the Nyquist samples are quantized into L = (as in table Q4) levels. Determine the following: i. Nyquist rate. ii. Number of binary digits required to encode each sample. iii. Number of binary digits per second (bits/s) required to encode the audio signal. iv. Minimum channel band width required to transmit this PCM signal. v. Sampling frequency if the audio signal is sampled at a rate of 10.0% lower than the minimum Nyquist's sampling frequency. Evaluate whether the Nyquist criterion satisfied. If the sampling rate does not fulfill the Nyquist criterion, explain what will happen to the transmitted signal. Table Q4 Students Name L number of levels f. kHz 32,768 16,384 12 14 LAKSHMI LJINA MAZOUN MOHAMMED 4,096 1,024 16 18
B- Draw the modulation and demodulation block diagram of AM-VSB. C- If m(t)-Am cos(wmt) v, find and sketch the spectrum of AM-DSB signal.