Using T-type flip flops, design and draw the circuit of a synchronous counter that counts the odd numbers 0-15 from the smallest to the largest in a continuous loop. When unintentionally come to numbers that are not in the counting index, the next number should be the nearest odd number after it in the counting index please provide. Make reference to minterms (SOP) in your transactions. Make sure the least significant bit is on the far right and sort the names in alphabetical order. do it. Make sure that the circuit you draw is understandable and the solutions are readable.

Using T-type flip flops, design and draw the circuit of a synchronous counter that counts the odd numbers 0-15 from the smallest to the largest in a continuous loop. When unintentionally come to numbers that are not in the counting index, the next number should be the nearest odd number after it in the counting index please provide. Make reference to minterms (SOP) in your transactions. Make sure the least significant bit is on the far right and sort the names in alphabetical order. do it. Make sure that the circuit you draw is understandable and the solutions are readable.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Draw a Moore-type state diagram and design a synchronous sequential circuit using D flip flops for a 1-input/1-output "sequence detector" for the sequence 11 (be sure to recognize overlapping sequences). Draw the final circuit. Draw a Moore-type state diagram and design a synchronous sequential circuit using D flip flops for a 1-input/1-output "sequence detector" for the sequence 100 (be sure to recognize overlapping sequences). Draw the final circuit. Draw a Moore-type state diagram and design a synchronous sequential circuit using D flip flops for a 1-input/1-output "sequence detector" for the sequence 110 (be sure to recognize overlapping sequences). Draw the final circuit. Draw a Moore-type state diagram and design a synchronous sequential circuit using D flip flops for a 1-input/1-output "sequence detector" for the sequence 000 (be sure to recognize overlapping sequences). Draw the final circuit. Draw a Moore-type state diagram and design a synchronous sequential circuit using D…
Design a synchronous BCD Counter based on the following conditions. If last digit of your roll number is odd then design down-counter with JK-Flip Flops by initializing the counter with last digit and count next five states. The counter should cycle back after counting five states. Hint: roll number = 169
Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit onany random input. Provide the following information as well:1. State table2. State diagram3. State equations4. Complete circuit diagram
Design a synchronous counter that operates according to the state diagram given below. Your design should involve only D-flip flops and minimum number of components. Show all the steps clearly. 110 00 001 ↑ 111 010 101
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
16. The following serial data are applied to the flip-flop through the AND gates as indicated in Figure 7-85 Ⓒ. Determine the resulting serial data that appear on the Qoutput. There is one clock pulse for each bit time. Assume that Q is initially 0 and that and PRE are HIGH. Rightmost bits are applied first. J₁: 1010011; J₂:0111010; J: 1111000; K: 0001110; K 1101100, K: 1010101 CLK K₁ CLR Figure 7-85 C K PRE -Q CLR
8. Analysis of Synchronous Counters. In the following figure, write the logic equation for ach input of each flip-flop. Determine the next state for state 010,011,100 as Q:Qi Qo sequence. CLK HIGH Jo с Ko lo J₁ с K₁ 2₁ J₂ с K₂ l₂
Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit on any random input. Provide the following information as well: 1. State table 2. State diagram 3. State equations 4. Complete circuit diagram
show the waveforms for each flip-flop output with respect For the ring counter in Figure to the clock. Assume that FF0 is initially SET and that the rest are RESET. Show at least ten clock pulses. D D. FFO FF1 FF2 FF3 FF4 FF5 FF6 FF7 FF8 FP9 CLK
Convert a single J-K flip flop to a T-flip flop. Include all steps involved. What is the next count if the counter started with 000 and 011 (unused states)? i want the anwer for the second qustion