Using z-transformation find the solution y(k) of the difference equation y(k+2)-y(k+1)+ 0.25y(k)= u(k+2) where the initial conditions are y(0) = 1 and y(1)= 2. The input is u(k) is the discrete-time unit step u(k)= 1 for k= 0, 1, 2, 3, 4... and u(k)=0 otherwise, which means that there are initial conditions for the input.

Using z-transformation find the solution y(k) of the difference equation y(k+2)-y(k+1)+ 0.25y(k)= u(k+2) where the initial conditions are y(0) = 1 and y(1)= 2. The input is u(k) is the discrete-time unit step u(k)= 1 for k= 0, 1, 2, 3, 4... and u(k)=0 otherwise, which means that there are initial conditions for the input.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2) Find k and for the system shown in Figure 2 by using = 0.5 and steady-state error (ess) 0.1 for a unit ramp input. R(s) Figure 2 k s(s+B) C(s)
The following plot is a step response of a sixth order system. 1. Find the time domain specifications i.e. Tp. Tri. T. and P.O. 2. Find a second order system whose response matches the given response in the following sense a. The percentage overshoot and rise time b. The peak time and settling time c. The rise time and settling time You have to find three systems Aroude 1 14 13) 12 UP E ON ST 06 0.5 DA 03 63 DI 0 6 A W . -CA P.O.= e √1-2 Ts= 4 ζωη Satisfying 2% criteria 10 Control Systems Homework Problem 3 100 M 16 18 20 Step Response for 24 21 20 30 The P.O. -In (100) √²+In² (²00) Tr Tp 2.16+0.60 On 0.3<≤0.8 Onv T 1-32 and 10% to 90% value
Figure in the below presents the direct form II realization of a difference equation. Assume that the resulting system is linear and time-invariant. v[n] x[n] yln] z1 1/3 -2 a) Find the direct form I realization. b) Find the difference equation described by the direct form I realization. c) Find the relation between v[n] and y[n]. Find the relation between v[n] and x[n]. Using these relations, verify that the relation between y[n] and x[n] in the direct form II realiza- tion is the same as your answer to part (b).
Consider the block diagram of a submersible vehicle shown below: K R(s) K1 s+K¡K2 Y(s) The steady-state tracking error to a unit step input R(s) is Select one: ess %3D ki+k2 a. k2 k1(k+k2) ess %3D b.
The following plot is a step response of a sixth order system. 1. Find the time domain specifications i.e. Tp. Tri. T. and P.O. 2. Find a second order system whose response matches the given response in the following sense a. The percentage overshoot and rise time b. The peak time and settling time c. The rise time and settling time You have to find three systems spred 13) "1 1 aut ON 071 0.3) DA 63) 61 6 2 B Control Systems Homework Problem 3 . 10 12 14 P.O. = e √1-² 100 4 Ts= Con Satisfying 2% criteria 10 18 20 Step Response for 24 The -In (100) 7²+In²(0) Tr 20 P.O. 100 Tp= 2.16+0.60 On 0.3≤ ≤0.8 @n 7 100 1-2 and 10% to 90% value
reduce the block diagram to canonical form andFind C (s). K is constant.
Report Requirements: 1. Write two -files to do the following for the system shown in the figure: K(2 - 4s + 20) (s + 2)(s + 4) R(s) C(s) a. Sketch the root locus, then from the root locus, find FOUR values of gains as follow: i. K that makes system response Overdamped. ii. K that makes system response Critical damped. iii. K that makes system response under damped (-0.707). iv. K that makes system marginally stable. b. By using values of gains found in (i, ii, iii), plot the step responses of the systems together. c. Complete the following table: % OS Tp Tr Ts wn a Overdamped Critical-damped Under damped Un damped 2- Find value of k required for the following system to meet the following requirements: Tr<0.2 second, Ts <3 seconds. R(s) + K(s? - 4s + 20) C(s) (s + 2)(s + 4) 4
2. Find the static error constants and the steady-state error for the digital system shown in Figure P2 if the inputs are a. u(t) b. tu(t) C. t²u(t) R(z) - 0.13(z + 1) (z-1)(z-0.74) C(z) Figure P2
Map this following expression into K-map , then use K-map to simplify expression(3 varia bles and standard SOP expression) Map this following expression into K-map , then use K-map to simplify expression Y(A,B,C) = E(m,,m,,m,,m, ,m, ,m, ,m,)
Show that the circuit is an equivalent circuit satisfied by the z-parameter equations.
Problem 2 Define the initial current , the final current Is, the time constant r, and the current i at 32 us. 0mll 12v The switch is closed at t-0.
find lappace inverse, please show steps