18713-40 The figure shows a pair of shaft-mounted spur gears having a diametral pitch of5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is32-hp at 1800 rev/min. Find the direction and magnitude of the forces acting onbearings A, B, C, and D.13-41 The figure shows the electric-motor frame dimensions for a 30-hp 900 rev/min motor.The frame is bolted to its support using four -in bolts spaced 11 in apart in the viewshown and 14 in apart when viewed from the end of the motor. A 4 diametral pitch20° spur pinion having 20 teeth and a face width of 2 in is keved to and fluch with3 in 3 inProblem 13-40

The diametral pitch of the given gear system is p=5 teeth/in. The number of teeth on the pinion is…

VThe figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is 32-hp at 1800 rev/min. Find the direction and magnitude of the forces acting on bearings A, B, C, and D.

VThe figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is 32-hp at 1800 rev/min. Find the direction and magnitude of the forces acting on bearings A, B, C, and D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. A helical gear has a normal diametral pitch of 12. a nor- mal pressure angle of 20°, 48 teeth, a…

Q: A 15 kW and 1200 motor drives a compressor at 300 a pair of spur gears having . The center-to-center…

A: Given DataP=15kWN1=1200rpmN2=300rpmc=400mmσP=210MPa

Q: 15. A straight bevel gear pair has the following data: Np = 25; NG = 50: P, = 10: 20° pressure…

Q: A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown in…

A: Given that Friction torque =T ω=15 N.mGear ratio =a=0.1 Gear efficiency η=90% =0.9Motor shaft torque…

Q: Q Two involute gears having module 3 mm and pressure angle 20 mesh externally to give a velocity…

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Q.7 A pair of parallel helical gears consists of a 20 teeth pinion mashing with a 40 teeth gear. The…

Q: 13-55 Gear 2, in the figure, has 16 teeth, a 20° transverse pressure angle, a 15° helix angle, and a…

A: Given that, Gear 2,Number of teeth, N2=16Pressure angle, φ=20°Helix angle, ψ=15°Modlue, m=4 mm,Gear…

Q: Q1 Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of…

Q: 13-31 Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the…

A: Given, Power in shaft a = Pa = 75 kW = 75000 W Rotational speed of a = Na = 1000 rpm Module of all…

Q: A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a…

A: Given: R=99% n_d = 2.5 N_p = 15 N_g = 60 P_d = 6 d_p = 2.50 in. b=1.25 in. n_p = 900 rpm To find:…

Q: 5. A driving gear at 20,000 rpm is used to drive a reduction gear delivering 2kW at 2,000 rpm. The…

A: 5. Given Data The power is: P=2 kW=2000 W The speed is: N=20000 rpm The pressure angle is: 20° The…

Q: Two spur gears in a simple train shown in Figure Q1 are having the same module, m=2 and their…

Q: A steel spur pinion has a pitch of 3 mm, 22 full-depth teeth, and a 20° pressure angle. The pinion…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: The figure shows a pair of shaft-mounted spur gears having an 18-tooth pinion driving a 45- tooth…

A: Given data: The number of teeth on the pinion, t1 = 18. The number of teeth on the gear, t2 = 45.…

Q: A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion…

A: Given Data The pitch circle diameter of the pinion is: dp=80 mm The velocity ratio is: 2:1 The…

Q: Q1 Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: See Figure P12–6. The shaft rotating at 310 rpm carries a spur pinion E having 36 teeth with a…

A: Power P=2πNT6020 hp=132×103 lbins=2π×310T60T=4066.15 lb. inTorque T=Ft.r4066.15=Ft×3 inFt=1355.38 lb

Q: The figure shows a 16T 20' straight bevel pinion driving a 32T gear, and the location of the bearing…

A: power,H = 2.5 hp RPM (n) = 248 rev/min

Q: The reducer input shaft shown in the figure is tapered It transmits moment with the help of a gear…

A: According to the working principle of the high-frequency crushers, the formula for calculating…

Q: - The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance= 660 mm…

A: Given data:

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: Answer: (a) Normal circular pitch: 0.4335 in (b) Normal diametral pitch: 7.2470 in (c) Axial pitch:…

Q: The Smm module with 40 number of teeth gear is used to transmit 42.3 kw power at 350 rpm .Find the…

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: Here Given Power P=5000 WattN1=720 rpmT1=20T2=50T3=30T4=60m=4mmϕ=20°Radius of…

Q: The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a…

A: Given Data: Speed of the 24T 6-pitch 20° pinion 2 is 900 rev/min clockwise. Power at which pinion…

Q: The figure shows a 16T 20' straight bevel pinion driving a 32T gear, and the location of the bearing…

A: Write the given data along with suitable variables.

Q: All three meshing gears shown in Figure Q6 have a module ot 5 mm and a 20" pressure anglU. Driving…

Q: Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-…

A: Given, P = 75 kW na=1000 rev/minm = 5 mmϕ=20oN2=17N3=34N4=51

Q: For the gear mechanism in the figure: P1 = 4 kW, η1 = 1000 rpm, z1 = 18, z2 = 36, z3 = 54, z4 = 108,…

A: This question is solved with the help of gear ratio formulae. Torque on gear 1,…

Q: The four helical gears shown in figure have a module in the normal plane of 4 mm and a pressure…

Q: For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The…

Q: The top half of a compound Epicyclic gearset is shown in Figure, with input shaft I rotating at a…

A: Given: The speed of shaft I and gear S1, = NI = 700 rpm (CW) The generating power by shaft I, PI =…

Q: .. The figure shows a pair of shaft-mounted spur gears having a diametrical pito teeth/in with a 14…

Q: 13-32 The 247 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 1000 rev/min and is…

Q: (a) Explain how to calculate the initial tension for a V-belt drive. (b) The figure shows a pair of…

A: (a) When a V belt drive is mounted between two pulleys, a small starting tension in the belt is…

Q: A pair of helical gears mounted on parallel shafts have P,=6, 20, and b-4 in. The 32-tooth pinion…

Q: For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The…

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: (a) Normal circular pitch: 0.43354 in (b) Normal diametral pitch: 7.24637 teeth/in (c) Axial pitch:…

Q: (d) A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown…

Q: For the meshing helical gears shown below, the normal pressure angle is 20 degrees, the helix angle…

A: Dear student, According to the guidelines I am allowed to answer only three…

Q: A gearbox with a compound reverted gear train transmits 25 horsepower with an input speed of 2500…

A: Given data Power = 25 hp = 18642.5 W Input speed = 2500 rev/min

Q: A compound epicyclic gear is shown in Fig. for Q.2. C and D form a compound wheel which rotates…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Q1 Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: 1. The figure shows a pair of shaft-mounted spur gears having a diametrical pitch of 6 teeth/in with…

A: NOTE:- As per our company guidelines we are supposed to answer only 3 sub-parts. Kindly repost other…

Q: Problem 2 A speed-reducer gearbox containing a compound reverted gear train transmits 35 horsepower…

Q: A spur gear train is made up of a set of gears as indicated in the sketch usinga gear configuration…

A: Note - As per our company guidelines we are allowed to answer only three subparts in case of…

Q: 1. Figure below shows a planetary gear train, determine the speed of link 6 when link 2 is rotating…

A: To find: The speed of the link 6. Given: The speed of link 2 is N2=1200 rpm. The link 1 is fixed.…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

187
13-40 The figure shows a pair of shaft-mounted spur gears having a diametral pitch of
5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is
32-hp at 1800 rev/min. Find the direction and magnitude of the forces acting on
bearings A, B, C, and D.
13-41 The figure shows the electric-motor frame dimensions for a 30-hp 900 rev/min motor.
The frame is bolted to its support using four -in bolts spaced 11 in apart in the view
shown and 14 in apart when viewed from the end of the motor. A 4 diametral pitch
20° spur pinion having 20 teeth and a face width of 2 in is keved to and fluch with
3 in 3 in
Problem 13-40

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given Data

Step 1

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is 28-hp at 1700 rev/min. Find the magnitude of the force acting on bearing D. 3 2 3 in 3 in The magnitude of the force acting on bearing Dis lbf.
13-31 Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock- wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler. (a) Find the force F3, that gear 3 exerts against shaft b. (b) Find the torque T4c that gear 4 exerts on shaft c. -517 -34T Problem 13-31 3 17T
The figure shows a pair of shaft-mounted spur gears having a module of 5 mm with an 18-tooth 20° pressure angle pinion driving a 45-tooth gear. The power input is 24 kW at 1800 rev/min counterclockwise into the pinion. Find the direction and magnitude of the forces acting on the shafts a and b. SOLUTION:
a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock- wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler. (a) Find the force F3b that gear 3 exerts against shaft b. (b) Find the torque T4c that gear 4 exerts on shaft
A pinion having 40 teeth drives a gear having 80 teeth. the profile of the gear is involute with pressure angle ( 22), 12 mm module and (14) mm addendum. Find 1-the length of contact2-Arc of contact 3-Contact ratio
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclockwise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.
The four helical gears shown in figure have a module in the normal plane of 4 mm and a pressure angle in the normal plane of 0.35 rad. The motor shaft rotates 550 rpm and transmits 20 kW. Other data are on the drawing. (a) What is the speed ratio between the motor (input) and output shafts? (b) Determine all force components that the 20-tooth pinion applies to the 50-tooth gear. Make a sketch showing these forces applied to the gear. (c) The same as part (b), except for the force components that the 50-tooth gear exerts on the 25- tooth pinion 100 50 teeth 200 125 25 teeth ψ = 0.35 rad right hand Motor 20 teeth ψ = 0.50 rad left hand 50 teeth Output
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler.(a) Find the force F3b that gear 3 exerts against shaft b.(b) Find the torque T4c that gear 4 exerts on shaft c.
Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and transmits a torque of 20 N-m. The torque transmitted by the gear is
The figure shows a schematic representation of a gear system. The gears are meshed with one another and can therefore not slip. The ring gear R is fixed, i.e. wR = 0. Gear A has an inner hub with radius rA(inner) = 0.3 m which is fixed to the rest of the gear, having a radius of FAlouter) = 0.8 m, and moves together as a unit. Gear A is in mesh with gear B which has a diameter of de = 1.5 m. Gear B has a clockwise angular velocity of wg = 2.1 rad/s. Determine the angular speed of gear A. B TA(outer R
3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20 3 = 30, 2, = 50 . Calculate the module of four gears and the tooth number of gear 1.
In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.