Water at 15.6 °C flows across a 20- cm-square plate with a velocity of 2 m/s. A thin strip, 5 mm wide, is placed on the plate at a distance of 10 cm from the leading edge. If the strip is heated to a temperature of 37.8 °C, calculate the heat lost from the strip.

Water at 15.6 °C flows across a 20- cm-square plate with a velocity of 2 m/s. A thin strip, 5 mm wide, is placed on the plate at a distance of 10 cm from the leading edge. If the strip is heated to a temperature of 37.8 °C, calculate the heat lost from the strip.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

A 2-cm diameter, 10-m long tube transports water at an average flow velocity of 8 m/s. The water enters at 20°C and leaves at 30°C. To compute for the Nusselt number of the water flow, what is the exact value of the temperature in °C on which the water properties should be based?
e- Water at 12 °C is to be heated to 60 °C by passing it over a bundle of 3-m-long, 2-cm-diameter resistance heater rods maintained at 95 °C. Water approaches the heater rod bundle in normal direction at a mean velocity of 1.2 m/s. The rods are arranged in-line with longitudinal and transverse pitches of SL = 4 cm and ST = 3 cm. Calculate the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise.
A long and wide heated plate is maintained at uniform temperature. You have to calculate the flux from the plate if a fluid is flowing over the plate at 1 m/s. The length of the plate in the direction of the flow is 10 m. The fluid is air. Temperature of the plate is 60°C and temperature of average heat 81-3 u 10°C.
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
A flat plate of width 1 m and length 0.2 m is maintained at a temperature of 32 °C. Water at 22 °C flows across the top of the plate in parallel flow (see diagram below). Determine (a) the average convection heat transfer coefficient, and (b) the convection heat transfer rate from the top of the plate when water has a flow rate of 0.5 m/s. Assume steady-state, and find water properties in the "Given information page". Water w = 1 m L= 0.2 m
An electronic device is cooled by water flowing through capillary holes drilled in the casing as shown in below figure. The temperature of the device casing is constant at 353 K. The capillary holes are 0.3 m long and 2.54x10-3 m in diameter. If water enters at a temperature of 333 K and flows at a velocity of 0.2 m/s, calculate the outlet temperature of the water. 0.3 m 0000000000 Surface Water 333 K 0.2 m/s 2.54 x 10m temperature = 353 K Water Capillary holes Single capillary
You are conducting a series of flow experiments in order to investigate flow across a horizontal flat plate. When water at 51.9°C flows across a flat plate, the distance from the front edge of the plate to where the transition from laminar to turbulent flow occurs is determined to be 314mm. 1. What is the bulk velocity of the water flowing over the plate? 2. If the experiment is done with Refrigerant-22 instead of water and the same distance from the edge is measured, what would the bulk velocity be? 3. Compare the velocity and thermal boundary layer thickness at the laminar/turbulent transition point of the two cases above and comment on your finding. 4. Based on the average convective heat transfer coefficient up to the laminar/turbulent transition distance, which fluid would yield a higher heat transfer rate under the specified conditions?
8. A lead pipe has 2 cm inside diameter, 3 cm outer diameter, length of 130 cm. Liquid water at 4°C flows through the pipe with a bulk velocity of 0.03 km/hr. Air is blown around the outside of the pipe at 20 deg C. The inside wall of the said pipe has a temperature of 8 deg Celsius. Density of liquid water= 1000 kg/m³ Cp water=4.210 J/kgK Viscosity of liquid water= 1.5674 x10° Pa.s thermal conductivity of lead = 35 W/mK thermal conductivity of water = 0.575 W/mK Find: Overall heat coefficient (U) based on outside surface area b. System's heat transfer rate Prandtl (Pr), Reynolds (Re) numbers and type of flow а. с.
Air (can be assumed as an ideal gas) at an ambient temperature of 30°C flows across (perpendicular to the length) a 2.5-m long vertical rod of diameter 50 cm. The approach velocity is measured to be 2.5 m/s. The surface of the pipe is at a uniform 90°C. 10 (a) What is the Grashof number in this situation? 767×10 65928 (b) What is the Reynolds number in this situation (c) Which convection mode is dominant free or forced convection? (d) The surface emissivity of the cylinder is 0.9 and the surrounding temperature is 30°C, what is the radiative heat transfer rate from the cylinder? 1790 w
Example 3: Air at 27◦C and 1 atm flows over a flat plate at a speed of 2 m/s. Assume that the plate is heated over its entire length to a temperature of 60◦C. Calculate the heat transferred in (a) the first 20 cm of the plate and (b) the first 40 cm of the plate.
Hand Sanitizer (70% propanol gel) needs to be transported on a floor in a hospital from a central location per floor. The room farthest from the source is 17.5-m away. The hand sanitizer enters the tubing at 20°C and 275 kPa absolute and exits the tubing at atmospheric conditions. The tubing can Flowrate/velocity Calculation. Hand sanitizer be considered smooth; however, there are two (2) 90° curved elbows and four (4) Tee Run throughs, and one (1) foot value (Refer to the Loss for Fittings table in Canvas). The density of the hand sanitizer is 955 kg/m3 and the viscosity is 4.5 cP. What is the flow rate that can be obtained if the tubing diameter is 4.5-mm?