Water at 20°C is siphoned from a reservoir as shown in Figure. For d= 5 cm and D= 15 cm, h = 5 m, determine the following: (a) Minimum flow rate that can be achieved without cavitation occurring in the piping system and (b) Maximum elevation of the highest point of the piping system to avoid cavitation. 5 m T= 20°C 10 m (2 d 4) 2 m

Water at 20°C is siphoned from a reservoir as shown in Figure. For d= 5 cm and D= 15 cm, h = 5 m, determine the following: (a) Minimum flow rate that can be achieved without cavitation occurring in the piping system and (b) Maximum elevation of the highest point of the piping system to avoid cavitation. 5 m T= 20°C 10 m (2 d 4) 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 20°C is siphoned from a reservoir as shown in following figure. For d = 8 cm and D = 16 cm, determine (a) the minimum flow rate that can be achieved without cavitation occurring in the piping system at points 2 and 3 and (b) the maximum elevation of the highest point of the piping system to avoid cavitation. (c) Draw the HGL and the EGL for this system? H (m) 4.0 HT= 20°C ա լ | 2 m 7m
Do not attempt wrong. If not sure let others expert do it. Don't waste it. Water is withdrawn with differential daily flowrate over 3 days from a groundwater well in a confined aquifer of T = 180m ^ 2 / d * ay Calculate the flowrate during the second day at an observation well 60m away from the main well, given that the discharge for the first day is 125 L/s and for the third day is 100L/s. The total head drop over the three days is 17m. The volume released per unit volume of aquifer per unit drop in the phreatic surface is 0.007.
Water at 20C with a density of 0.9982 g/cc and a viscosity of 1 cP is flowing from an open reservoir throught he piping system below and assumed to be discharged at an atmospheric condition. The piping system is composed of 3 m - 3” schedule 40 pipe with a standard gate valve wide open installed and 6 m - 2” schedule 40 pipe. The reservoir has a level of water of 3.5 m. Calculate the average volumetric flow rate in liters per minute. (Use equation 6-37 of Perry’s Handbook (9th edition) to calculate for fanning friction factor).
A pump can lift water at a discharge of 0.15 m³/s to a head of 25 m. The critical cavitation number (oc) for the pump is found to be 0.144. The pump is to be installed at a location where the barometric pressure is 9.8 m of water and the vapour pressure of water is 0.30 of water. The intake pipe friction loss is 0.40 m. Using the minimum value of NPSH (Net Positive Suction Head), the maximum allowable elevation above the sump water surface at which the pump can be located is
A water flow rate of 10 lt/s with a maximum ΔP = 8400 Pa pressure loss (PA-PB) per 30 m horizontal lengthFind the minimum acceptable diameter of a steel pipe with ε = 0.005 cm to ensure its transmission (γsu = 9810N/m3, νsu = 1*10-6 m2nd/s) (Diameters of steel pipes produced: D=3.125 cm, 3.75 cm, 4.375 cm, 5.0 cm, 5.625 cm, 6.25 cm, 6.875 cm, 7.5 cm, 8.75cm and 10 cm)
A pump can lift water at a discharge of 0.15 m³/s to a head of 25 m. The critical cavitation number (o) for the pump is found to be 0.144. The pump is to be installed at a location where the barometric pressure is 9.8 m of water and the vapour pressure of water is 0.30 m of water. The intake pipe friction loss is 0.40 m. Using the minimum value of NPSH (Net Positive Suction Head), the maximum allowable elevation above the sump water surface at which the pump can be located is
A semi-modular pipe outlet of diameter 16 cm is to be installed on adistributary with its bed level and full supply level at 100.3 and 101.5 m, respectively. Themaximum water level in the watercourse is at 101.15 m. Set the outlet for maximum dischargeand calculate the same. The coefficient C in the discharge in the equation may be takenas 0.62. Is the setting proportional, subproportional or hyper-proportional?
HYDRAULICSFrom the figure shown, determine the flow in the open channel in cubic meter per second if the coefficient of discharge is 0.80NEED ASAP. PROVIDE COMNPLETE SOLUTION THANKS
In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B. Calculate (a) the flow rate in each of the branches and (b) the pres- sure difference PA PB. Include the effect of the minor losses in the lower branch of the system. The total length of pipe in the lower branch is 60 m. The elbows are standard.
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
The vapor pressure of water at 25 degrees Celsius is 23.8 mmHg. The atmospheric pressure is 14.6 psi. In the system shown below, in order to avoid cavitation, what should be the relative location of the pump (Z₂) if the total head loss from reservoir surface to pump entrance is 8.3 m? The pump is a Taco® Model 5009 centrifugal pump (diameter of 9.25 in. and operating at 1160 rpm) with a discharge of 750 GPM. Hint: Use the performance curves in Problem 2 for the pump. b' Pump 247 Reservoir Zo' O The pump should be located at least 1.99 ft above the water surface in the reservoir. O The pump should be located at least 1.99 ft below the water surface in the reservoir. O The pump should be located at least 3.78 above the water surface in the reservoir. O The pump should be located at least 3.78 ft below the water surface in the reservoir.
Problem 6:Water at 20 ̊C is siphoned from a reservoir as shown in the Figure. For d = 7.5 cm and D=15cm, determine the following:(a) the maximum flow rate (in m3/s) that can be achieved without cavitation occurring in thepipe system,(b) the maximum elevation (in m) of the highest point of the piping system to avoidcavitation.(c) Also, discuss the ways of increasing the maximum elevation of the highest point of thepiping system to avoid cavitation