Water flows through the curved pipe shown in the figure below where point X denotes the center of gravity of the system. Considering the weight of the pipe and water with-in as WG which acts at a distance of X m from pipe axis, answer the following questions: 1) What are the horizontal and vertical components of the force provided by the flange at point A? 2) What is the moment provided by the flange at point A?

Water flows through the curved pipe shown in the figure below where point X denotes the center of gravity of the system. Considering the weight of the pipe and water with-in as WG which acts at a distance of X m from pipe axis, answer the following questions: 1) What are the horizontal and vertical components of the force provided by the flange at point A? 2) What is the moment provided by the flange at point A?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertical dam has a semicircular gate as shown in the figure. The total depth d of the figure is 24 m, the height h of air above the water level is 4 m, and the width w of the gate is 4 m. Find the hydrostatic force against the gate. (Round your answer to the nearest whole number. Use 9.8 m/s2 for the acceleration due to gravity. Recall that the mass density of water is 1000 kg/m3.)
The cylindrical tank in the figure below has a hemispherical end cap ABC and dimensions R =1 ft; b = 3 ft; d = 0.4 ft and h = 0.5 ft. The tank if filled with oil of specific gravity 0.9 and sits in a pool of water as shown (water is outside the tank). The volume of a sphere is: V_sphere= 4/3 Ttr^3. Calculate the moment about the point C [lb-ft]. Report magnitude. 4 =l, = 0.259mr? b h d A R R Oil B Oil Water R Side view
A pressurized tank of water is used to create a fountain, as illustrated. Assume that the water's free surface area in the tank is very large relative to the pipe's cross-sectional area, which is circu- lar with diameter d 1.0 cm. The small pipe bend has height = 10.0 cm. At the instant when 0.75 m, H = 2.5 m, and the gauge measures a pressure of Pgauge 20.0 kPa, the water spray reaches a height L above the pipe exit. h = = = Neglecting viscous effects, determine the height of the spray, L.
In the following picture, you can see a concrete dam (trapezoid ABEO) and water behind it (rectangle BCED). Water applies a hydrostatic force to the dam, which causes overturning moment about point O. What is the minimum value of X to avoid overturning of the dam? Consider Pconcrete = 2.5 Mg/m³ and pwater = 1 Mg/m³. AB and BE are 1 m and 6 m, respectively. Also, width of the dam, normal to the plane of the figure, is 1 m. 1B 6 m Concrete Water -
A vertical dam has a semicircular gate as shown in the figure. The total depth d of the figure is 12 m, the height h of air above the water level is 2 m, and the width w of the gate is 10 m. Find the hydrostatic force (in N) against the gate. (Round your answer to the nearest whole number. Use 9.8 m/s2 for the acceleration due to gravity. Recall that the weight density of water is 1,000 kg/m³.) 1040542 12 m XN 10 m 2 m water level Ⓡ
The rectangular gate CD is 1.8 m wide and 2 m long as shown in the figure below. Water 2.0 m 2.0 m Hinge y 1. Extrapolate line CD to the surface and establish your origin and xy coordinate system. 2. Estimate the distance y. from surface to the centroid of the gate. 3. Estimate the vertical distance he from the surface to the centroid of the gate. 4. Estimate the magnitude of the resultant force (due to water column) applied on the gate, FR. 5. Estimate the distance yR from surface to the pressure point. 6. Draw on the figure above an arrow for the resultant force (FR) calculated in part (4) above. 7. Determine the weight of the gate necessary to keep it closed.
A gate of a water tank is kept in the closed position by applying a force F as shown in the figure. The depth of water (h) is 1.80 m. The height of the gate (H) is 0.500 m, and the width of the gate (into the paper) is 1 m. The gate is designed so that it can rotate around the hinge as shown. h (m) H (m) F Gate Hinge Part A Calculate the minimum force F required to keep the gate in the closed position. Express your answer to three significant figures VO ΑΣΦ Submit Provide Feedback Constants Request Answer **** ? Next KN
A vertical dam has a semicircular gate as shown in the figure. The total depth d of the figure is 10 m, the height h of air above the water level is 2 m, and the width w of the gate is 4 m. 2 m 10 m water level 4 m Set up an integral that can be used to find the hydrostatic force (in N) against the gate. (Use 9.8 m/s² for the acceleration due to gravity. Assume that the weight density of this water is 1,000 kg/m³.) X (1,000)(9.8) dx Find the hydrostatic force (in N) against the gate. (Round your answer to the nearest whole number.) N
5. Gate ABC is shaped in the form of a circular arc and pivots about point O. The arc extends a width b in the plane of the figure. 6 m Water A R = 6m 6 m Questions: (a) Determine the horizontal component of the resultant hydrostatic force (per unit width) acting on the gate. (b) Determine the vertical component of the resultant hydrostatic force (per unit width) acting on the gate. (c) Determine the magnitude and direction of the resultant hydrostatic force. (d) Does the line of action of this force pass through point O? Justify your answer.
A dam is used to store water, and a rectangular gate which is hinged at its bottom edge is used to control the flow as shown in figure 1. For this gate, width = 1 m (in the direction of the page) , α = 65°, h1 = 1 m, and h2 = 5 m. Figure 1: Schematic for task 1. (Giancoli et al.) a. Describe the forces acting on the gate and the center of pressure. b. Determine the resultant force and the position of the center of pressure on the gate. c. What is the maximum gate mass that is needed for it not to fall? d. Show yc, yR, hc, hR, FR, and W on the free body diagram.
A source and sink of equal strength, m = 25 m²ls, are near a wall, as in Fig. induced by this pair at point A on the wall. 5- 4. . Find the resultant velocity 4 m 3 m 4 m 3 m
Calculate the horizontal and vertical forces acting on the cylindrical shape and calculate the line of action of the horizontal forces if the gate length is 6m