kgWater (p=1000- ) flows smoothly through a pipe that has an elevation change and a change in cross-sectional area. Using the information given below, answer the following questions.3●PA=140650.00ParA=0.420m"B=1.310m• y=3.00mVA=5.00mSVB=0.51 mSmAΤΑ1. What is PB, the pressure in region B?123880.05Pa153019.95Pa182419.95Pa98880.05Pa2. The volume flow rate through region A isyBthe volume flow rate through region B due to---TB

Name: kgWater (p=1000- ) flows smoothly through a pipe that has an elevatio
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: kgWater (p=1000- ) flows smoothly through a pipe that has an elevation change and a change in cross-sectional area. Using the information given below, answer the following questions.3●PA=140650.00ParA=0.420m"B=1.310m• y=3.00mVA=5.00mSVB=0.51 mSmAΤΑ1

Given, density of water , ρ = 1000 kg/m3 PA = 140650.00 ParA = 0.420 mrB = 1.310 my = 3.00 mvA =…

Science

Physics

Water (p=1000) flows smoothly through a pipe that has an elevation change and a change in cross-sectional area. Using the information given below, answer the following questions. • PA=140650.00Pa • A=0.420m re 1.310m • y=3.00m . VA=5.00m VB=0.51 m S A 1. What is PB, the pressure in region B? B TB

Water (p=1000) flows smoothly through a pipe that has an elevation change and a change in cross-sectional area. Using the information given below, answer the following questions. • PA=140650.00Pa • A=0.420m re 1.310m • y=3.00m . VA=5.00m VB=0.51 m S A 1. What is PB, the pressure in region B? B TB

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Air flows at 210 m/s through the pipe. The temperature is 400 K and the absolute stagnation pressure is 280 kPa. Assume isentropic flow. For air R = 286.9 J/[kg - K] and k=1.40. (Figure 1) Figure 0.3 m
Solve the problems below. 1. A wind blows at the speec. of 30 m/s across a 175 m2 flat roof of a house. (a) Whar is the pressure difference between the inside of the house and the outside of the house just above the roof? (Assume that the air pressure inside the house is atmospheric pressure.) (b) Whar is the force on the roof due to the pressure difference? 2. Water e:nters a house frorm a ground pipe with an inside dianmeter of 0.02 m at an absolute pressure of 4.0 x 105 Pa. A pipe that is 0.01 m in diameter leads to the second-floor bathroom 5.0m above the ground floor. The flow speed ar the ground pipe :s 1.5 m/s. Find the following: (a) flow speed on the second floor; and (b) pressure. 3. Water flows at a rate of 800 cm3/min in a pipe of varying cross-sectional areas. Calculate the veloc.ty of the water at the section where: (a) the radius is 3.0 cm; and (b) the radius is 5.0 cm 2021/3/20 21:08
System A is in equilibrium with reservoir B. They are Einstein solids with the following specifications. NA = 2 NB = 40 qtotal = 20 How many macrostates are available? State your answer as an integer.
Q1/ A presssure of 102 kN/m? was applied on a confined fluid of 784 kg/m by a circular cross-sectional piston. Calculate the radius of the piston if its force was 32 kN.
Given: Pi constant to be used: 3.14159Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHgLiquid sample: density = 4 ml; time of flow = 4.5 seconds 1. What is the pressure in MKS unit? Your answer here will be used for the next item(s). 2. What is the pressure in CGS unit? Your answer here will be used for the next item(s). 3. What is the viscosity of the liquid? Your answer here will be used for the next item(s). 4. If the weight was given as 8.5 grams, what will be the density of the liquid? Your answer here will be used for the next item(s). 5. What is the kinematic viscosity of the liquid? 6. What is the fluidity of the liquid?
An oil drop with the diameter of 1mm, is in the contact with the air with the pressure of 80 KN/m2. i. Find the dimension of surface tension in MLT system ii. If the surface tension of the drop be 42.27x103 N/m, find the pressure difference of the drop. iii. Calculate the internal pressure of the drop. iv. Explain briefly, if the oil drop replace by oil bubble, what changes will happen in internal pressure?
The brake piston consists of a full circular part. Its cross section is shown in. Suppose that a = 16 mm, Part A b=90 mm, c = 55 mm, d=45 mm, e = 35 mm. f = 40 mm. 29 μA e Submit a Determine the interior surface area of the brake piston. Express your answer to four significant figures and include the appropriate units. ▸ View Available Hint(s) Value Units C ?
At 20 ° C, the surface tension of water is 0.073 N/m. A soap film is holding up the entire weight of a horizontal slide wire, as shown in the figure below. 2yl Part A If the wire has a length of 2.2 cm and a diameter of 0.10 cm , what is its density? Express your answer in kilograms per meter cubed. ? kg/m? Submit Request Answer
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 220.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 10.00 MN. pressure vessel bolts alo W Ar side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x1 Explanation Check 2021 McGraw-Hill Education. All Rights Reserved. Terms of Use I Privacy Accessibility lenovO .ddle WebEx at 3pm (dia just before 3pm) Resp 1-650-479-3208 Access Code (meeting Number): 737 129 915 Dois! 3134
Can you help me draw a diagram for each number? thank you 1.)The velocity of the water at the entrance and exit of a pipe are 10 m/s and 3 m/s,respectively. The volume of water flowing inside the tube is 18000 m 3 . What isthe kinetic energy of the water measured at the exit of the pipe? 2. If the exit of the pipe in problem 1 is located at the ground level, what is theelevation of the pipe inlet if all the potential energy is converted to the kineticenergy in problem 1? 3. What is the total thermodynamic heat released by heating 2 kg of solid ice at 0 0 C(2093 J/kg-K) to 100 0 C without steam formation?
ing.pearson.com/?courseld=12521655&key=322254521541138373232024#/ In the event of an emergency, a nuclear reactor is shut down by dropping the control rod R, having a weight of 20 lb, into the reactor core C, as shown in (Figure 1). A If the rod is immersed in "heavy" water, which offers a drag resistance to downward motion of FD = (0.25v) lb, where v is the velocity of the rod in ft/s, determine the distance s it must descend into the reactor core when it attains a speed of 14 ft/s. The rod is released from rest when s = 0. Neglect the effects of buoyancy. Express your answer in feet to three significant figures. Figure R Search FD 1 of 1 > V = VAΣ ΜΕ ΑΣΦ JA vec 20 ? Submit Request Answer Provide Feedback ft Next > 3:41 PM 4/23/2024
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 450.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.50 MN. pressure vessel bolts do Ar side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm Ox10 Explanation Check 2021 McGraw-Hill Education. All Rights Reserved. Terms of Use | Privacy Accessibility Activity Details MacBook Air 4> F19 80 888 FB F7 F6 F4 F5 F2 F3 F1 & 云 %24 %23