Needs Complete typed solution with complete explanation and 100 % accuracy. Don't use chat gpt or any ai Part AWhat are the physical principles behind the action of the heat sinks? That is, how do they reduce the temperature of the hot side of the TEC?Select the correct answer(s), there may be more than one.Heat capacityThermal conductionConvectionRadiationPhase transformationLatent heatSubmitPart BRequest AnswerWhat is the purpose of the heat sink compound (thermal paste)?To increase thermal conduction between heat sinks.To increase electrical conduction between heat sinks.To lubricate the heat sinks and prevent them from sticking.To electrically insulate the heat sinks.To hold heat sinks together.To absorb heat from the heat sinks.Submit Request Answer

Given, A heat sink and a heat sink compound problem.To Find - a) principle of heat sink…

What are the physical principles behind the action of the heat sinks? That is, how do they reduce the temperature of the hot side of the TEC? Select the correct answer(s), there may be more than one. Heat capacity Thermal conduction Convection Radiation Phase transformation Latent heat Submit Request Answer Part B What is the purpose of the heat sink compound (thermal paste)? To increase thermal conduction between heat sinks. To increase electrical conduction between heat sinks. To lubricate the heat sinks and prevent them from sticking. To electrically insulate the heat sinks. To hold heat sinks together. To absorb heat from the heat sinks.

What are the physical principles behind the action of the heat sinks? That is, how do they reduce the temperature of the hot side of the TEC? Select the correct answer(s), there may be more than one. Heat capacity Thermal conduction Convection Radiation Phase transformation Latent heat Submit Request Answer Part B What is the purpose of the heat sink compound (thermal paste)? To increase thermal conduction between heat sinks. To increase electrical conduction between heat sinks. To lubricate the heat sinks and prevent them from sticking. To electrically insulate the heat sinks. To hold heat sinks together. To absorb heat from the heat sinks.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.31P

See similar textbooks

Similar questions

Solve this with diagram: An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to? Solve it with resistors method
Solve this with diagram: An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to?
Solve for this : An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to?
Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter uninsulated steel pipe. Assume the pipe wall thickness is 0.25-inches, the pipe interior convective heat loss (hi) is 500 BTU/hr-ft2-oF, and the pipe outside convective heat loss ho 20 BTU/hr-ft2-oF, k steel is 25 BTU/hr-ft-oF, and k insulaton is 0.023 BTU/hr-ft-oF. (hint - calculate heat loss with and without insulation.
An industrial process to harden ball bearings involves quenching them in a cooling bath at40°C. The bearings move on a conveyor belt from an oven, through the cooling bath, andthen out to air dry. The oven is long enough that the bearings reach a uniform temperatureof 900°C before exiting the oven. The ball bearings must exit the cooling bath no hotterthan 100°C. The ball bearings are made of AISI 316 Stainless Steel and the convectioncoefficient between the bearings and the cooling fluid can be considered constant at ℎ =600 W m2-K⁄ . You can find thermophysical properties of different materials in Appendix Aof the Bergman textbook.a) What is the largest diameter ball bearing that can be treated as thermally lumpedfor this cooling process? Take ? at a reasonable average temperature for this process.You do not need to interpolate if the average temperature is within ~30 K of a giventable value.b) The cooling bath is 5 m long. Using the diameter you found in part (a), estimate thespeed…
For bacteriological testing of water supplies and in medical clinics, samples must routinely be incubated for 24 h at 37°C. Peace Corps volunteer and MIT engineer Amy Smith invented a low-cost, low-maintenance incubator. The incubator consists of a foam-insulated box containing a waxy material that melts at 37.0°C interspersed among tubes, dishes, or bottles containing the test samples and growth medium (bacteria food). Outside the box, the waxy material is first melted by a stove or solar energy collector. Then the waxy material is put into the box to keep the test samples warm as the material solidifies. The heat of fusion of the phase-change material is 205 kJ/kg. Model the insulation as a panel with surface area 0.490 m2, thickness 4.50 cm, and conductivity 0.012 0 W/m ? °C. Assume the exterior temperature is 23.0°C for 12.0 h and 16.0°C for 12.0 h. (a) What mass of the waxy material is required to conduct the bacteriological test? (b) Explain why your calculation can be done…
Problem 1: Determine the amount of heat removed from 1.5 kg of bologna (sausage) when cooled from 24C to -7C.Assume MC of 59% and at -7C, 22% won’t be frozen. Problem 2: Estimate the thermal diffusivity of butter at 20°C.
You are designing a PCB laid horizontally on the ground. The PCB surface temperature can’t exceed 85℃ and has a size of 96mm x 90mm. Tinfinity = 45oC. "p" is the perimeter of the plate a) Calculate the Rayleigh number. b) If the PCB is laid hot-side UP, what is the Nusselt number and heat transfer coefficient? c) If the PCB is laid hot-side DOWN, what is the Nusselt number and heat transfer coefficient? d) Given your results from b and c, which one has better heat transfer? In that case, what is the maximum power dissipation the board can put out? Properties of Air:k = 0.025 W/mkPr = 0.72v = 1.847 x 10−5u = 16.84 x10−6p = 1.2 kg/m3B =1/ Tf (idwal gass)
A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?
Industrial pipes One of the ways to keep a pipe warm is by means of a steam tracer, through which an electrical resistance is used around the pipe and in a helical shape throughout its diameter?
Trasient Cooling What are some of the factors and assumptions that would casue a different between the experimential convection coefficient, hexp, and the theorectical htheo?
(a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.