What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to the upper reservoir ? Hint: [The head loss in the pipes is given in the figure as a function of water velocity]. Elevation = 150m Water Elevation 100m h=45v-12g d=15cm Water Pump h=22.5v 12g d=20cm Elevation 40m

What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to the upper reservoir ? Hint: [The head loss in the pipes is given in the figure as a function of water velocity]. Elevation = 150m Water Elevation 100m h=45v-12g d=15cm Water Pump h=22.5v 12g d=20cm Elevation 40m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A confined aquifer underlies an unconfined aquifer as shown in the illustration below. Given the following: h1 is 45m, h2 is 33m, D1 is 85m, D2 is 38m, k1 is 27m/day, k2 is 35m/day, and Lis 2km. Calculate the discharge per two meter from one stream to another stream in meters volume per day. h1 ki D1 D2 h2 k2
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and - is into the reservoir) Assume ha = 50 m, hg = 60 m, hc = 20 m, ₁ = 100 m, ₂ = 200 m, and 3 = 400 m. QA = QB = Qc = i 0.01259 0.02125 0.02394 Elevation = h D₂=0.08 m l₂ = 0.020 m^3/s V m^3/s V m^3/s V Elevation = B ܓܝܪ ܩܝܡܗ ܘܐܡܡܢ D,= 0.10 m f₁ = 0.015 D.= 0.08 m f = 0.020 Elevation - he == ▼ C
Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water surface elevation in reservoir A if a flow of 0.03m^3/s is to occur in the cast iron pipe? Use n=0.011 for all pipes. Elevation = ? Water T= 10°C Elevation = 110 m B L = 150 m D = 15 cm Cast-iron pipe L= 100 m, D = 20 cm, cast-iron pipe
ASAP
The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft³/s. Determine the following: a. the flow rate (ft³/s) in pipe 2, Q2. b. the flow rate (ft³/s) in pipe 3, Q3. C. the head loss (ft) in pipe 3, hL3, pipe L (ft) d (in) f 1 5000 36 0.0157 2 1500 24 0.0162 3 4000 18 0.0177 A В
Q4 A pump is used to circulate the water from the lower to the upper reservoir through a pipe system shown in the figure below. The difference in elevation between these reservoirs is 200 m. find the head delivered by the pump and its power if the discharge is 100 L/s? KL = 1.0 "exit Pump KL = 1.5 elbow = 5.0 Pipe length 500 m Pipe diameter 0.25 m K₁=0.8 Pipe roughness=0.004 m HKL
Consider the figure shown. The discharge of reservoir a is 400 li/sec. Solve for the length of pipe 2 if the flow rate of pipe 1 is 240 li/sec and the elevation of point D. El. 50m A El. 40m B L1=1200m D1=650mm fi =0.02 L3=4700m D3 =350mm f3 =0.022 Node L2= ? D2=600mm f2 =0.02 L4=4600m D4=500mm f4 =0.019 El. C Answer: Length of pipe 2 = 1809.262m, Elevation of D = 15.46m
Three pipes 1,2 and 3 connect three reservoirs A, B and C, respectively, and meet at junction D. The elevation of A is 300 m while that of C is 277m. The rate of flow out of the reservoir B is 560Lit/sec. Pipe Length (m) Diameter (mm) Friction Factor 1 1200 800 0.0175 2 800 450 0.0208 3 1800 500 0.0183 Which of the following nearly gives the rate of flow in pipe 1? a. 45.91 L/s b. 122 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the rate of flow in pipe 3? a. 100.22 L/s b. 45.91 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the elevation of reservoir B? a. 360.55 m b. 336.67 m c. 323.37 m d. 3.90 m
Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table. Elevation Reservoir A 80m в 50m 20m Pipe Diameter Length friction factor AP 400mm 1800m 0.027 BP 500mm 2000m 0.02 СР 700mm 3500m 0.025 El. A El. El.
Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by the pump (in kilowatte) talpump water at 0.085 m/s at 20°C from the lower to the upper reservoir? Deo A Figuro 2: Pumping from lower to higher elevation The head loss in the pipes is h, 0.018 where Lis the length of the pipe in metors, and D is the diameter of the pipe in meters. D 25 Sketch the HGL and EGL for the system
4) For the system given in the figure, find the elevation of Reservoir D and the flow direction in pipe 6. Neglect minor losses. El 80 m V A Pipe 1 2 3 4 ||| 5 6 L (m) 600 600 600 700 300 300 P D(mm) 600 600 450 450 450 600 El 90 m B 2 f 0.025 0.025 0.03 0.03 0.03 0.03 3 El 60 m V с 5 6 E1 = ? D
Question 1: The PVC pipeline (ε = 0.0015) depicted in figure below is 150 m. Determine the diameter of the pipe that can provide a flow rate is 0.8 m³/s if the height h is 12 m. Ignore minor losses. water temperature is 4°C. U= h 497 x 10-6 (T + 42.5)1.5 2 m