What is the hex representation of thegiven RISC-V instruction? Note: justtranslate the beq instructionbeq x7, x7, loopinst ... 1inst ...inst ... 3inst ... 4inst ... 52loop:assume loop is 6 instructions away frombeq.beq x19, x10, offset = 16 bytes13-bit immediate, imm[12:0], with value 16Op00000010000imm[0] discarded,always zeroimm[12]0 000000 01010 | 10011imm[11]|1000 0 1100011BEQ imm[4:1]000imm[10:5] rs2=10 rs1=19BRANCH

Solution Instruction: beq x5, x5, loop offset = 4 13-bit immediate imm[12:0] = 0 0 000000 0010 0…

What is the hex representation of the given RISC-V instruction? Note: just translate the beq instruction beq x7, x7, loop inst ... 1 inst ... inst ... 3 inst ... 4 inst ... 5 2 loop: assume loop is 6 instructions away from beq. beg x19, x10, offset = 16 bytes 13-bit immediate, imm[12:0), with value 16 opo000001000 imm[0] discarded, salways zero

What is the hex representation of the given RISC-V instruction? Note: just translate the beq instruction beq x7, x7, loop inst ... 1 inst ... inst ... 3 inst ... 4 inst ... 5 2 loop: assume loop is 6 instructions away from beq. beg x19, x10, offset = 16 bytes 13-bit immediate, imm[12:0), with value 16 opo000001000 imm[0] discarded, salways zero

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Registers in RISC-V are 64-bit. For the sake of simplicity, consider the following instructions operating on 32-bit registers. Assume that registers x5 and x6 hold the values 0xBBBBBBBB and 0x00000000, respectively. What is the value in x6 for the followingslli x6, x5, 6 Using the result from the part above, what is the value in x6 for the following instruction. srli x6, x6, 6
What is the hex representation of the given RISC-V instruction? jal x5, loop assume loop is at offset O×3FF1.
Consider a RISC-V assembly function func1. func1 has three passing arguments stored in registers a0, a1 and a2, uses temporary registers t0-t3 and saved registers s4–s10. func1 needs to call func2 and other functions may call func1 func2 has two passing arguments stored in registers a0 and a1, respectively. In func1, after the program returns to func1 from func2, the code needs the original values stored in registers t1 and a0 before it calls func2. How many words are the stack frames of function func1? Indicate which registers are stored on the stack of func1? pseudo-instructions are not allowed except “j target_label” and “jr ra”.
Complete the following table: MIPS Instruction op code rs rt rd shamt funct imm. /address Hexadecimal Representation add $t4, $s2, $s1 addi $s0, $t0, 123 lw $s6, -88($t7) Note: In MIPS register file, temporary registers $t0-$t7 have indices 8-15 (respec- tively). Also, the saved registers $s0-$s7 have indices 16-23 (respectively).
Find the pyhsical destination adress of last instruction below. MOV BX,0AAH MOV AX,1BBH MOV DS,AX MOV[BX],AX
Q5 Please convert the following C/C++ function to RISC-V assembly (RV321). Function: swap Registers: ra = x1 (return address) &v[0] -> a0 = x10 (arguments/return values) k-> a1 = x11 (arguments/return values) to = x5 (temporary) t1 = x6 (temporary) t2 = x7 (temporary) hint: void swap(int v[], int k) { int temp; temp = v[k]; v[k] = v[k+1]; v[k+1] = temp; %3D }
Translate the below C code into RISC-V architecture, assuming that the values of i and j are placed in registers x23 and x24 respectively. The base address of array B is in register x30, and the base address of array C is in register x31. C[7] = B[i+j];
Flagonly in RISC-V (RVS) answer the following both question, thumps up if both Write an instruction that subtracts 1245 (in decimal) from x20 and stores the result in x22. Write an instruction that multiplies the signed integer in x14 by 4096 (in decimal) and stores the result in x18.
You need to write in hexadecimal (E.g: OX00114A63) for the following RISC-V assembly instruction: sub ra,gp,t1 * WARNING: You MUST write the Ox followed by the 8 hexadecimal digits all in UPPER case. If needed, add extra zeroes to have the 8 digits (this is auto graded, so no spaces, underscores or lower case). In the previous hexadecimal example Ox00114a63 is incorrect, OX114A63 is also incorrect, and 00114A63 is also incorrect. Only OX00114A63 is correct.
Q1. Write microcode for the execution part of the following CISC instruction. Give both a register transfer description and binary or hexadecimal representations. Add with carry: R[DR] + R[SA]+R[SB]+c Action Address MZ CA RW DX MD BS PS FS LC MA MB AX BX CS
Consider the instruction ADD R1, M (R1 = R1 + [M]). M is the memory address of the operand. It is a two-word instruction – first word is the op-code and the second word is the address of the operand. Give the RTL description for the complete execution (including fetch phase) of the instruction.
NO HANDWRITTEN Find the machine code for the following instruction in RISC-V. Assume all instructions are labeled sequentially, for example, I1, I2, I3, …, I200. I10 : BGE x10, x20, I100