11 What is the primary reason for adopting transposition of conductors in a three phase distribution system?O A. To balance the currents in an asymmetric arrangement of phase conductorsO B. To reduce the resistances of the phase conductorsO C. To increase the reactive voltage drop along the length of the lineO D. To reduce the reactances of the phase conductors

In this question we will write about transposition of conductors in 3 phase distribution system....

What is the primary reason for adopting transposition of conductors in a three phase distribution syster O A. To balance the currents in an asymmetric arrangement of phase conductors B. To reduce the resistances of the phase conductors C. To increase the reactive voltage drop along the length of the line D. To reduce the reactances of the phase conductors

What is the primary reason for adopting transposition of conductors in a three phase distribution syster O A. To balance the currents in an asymmetric arrangement of phase conductors B. To reduce the resistances of the phase conductors C. To increase the reactive voltage drop along the length of the line D. To reduce the reactances of the phase conductors

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.21MCQ: In order to avoid difficulties with third-harmonic exciting current, which three-phase transformer...

See similar textbooks

Similar questions

In a three-phase line, in order to avoid unequal phase inductances due to unbalanced flux linkages, what technique is used?
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
One advantages of load balancing is that each phase conductor carries the ? current value
What is the colour of neutral conductor in single -phase a.c. supply, a. Orange O b. Red O c. Black O d. Green
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
What are two main types of three-phase connections
Discuss how delta connection is achieved in three-phase systems?
In order to avoid difficulties with third-harmonic exciting current, which three-phase transformer connection is seldom used for step-up transformers between a generator and a transmission line in power systems. (a) Y- (b) -Y (c) Y-Y
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
2-What is the relationship between phase and line quantities in balanced star and delta connections in three phase circuit balanced ? Why?