What is the purpose of address decoding and explain the difference between full and partial address decoding. Assuming the address bus is 16-bit wide, using the address lines with no additional logical gates, how many 1024-Byte memory devices could be supported if each has a single Chip-Enable pin? Explain your answer.

What is the purpose of address decoding and explain the difference between full and partial address decoding. Assuming the address bus is 16-bit wide, using the address lines with no additional logical gates, how many 1024-Byte memory devices could be supported if each has a single Chip-Enable pin? Explain your answer.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter11: Operating Systems

Section: Chapter Questions

Problem 30VE

See similar textbooks

Similar questions

If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
For a computer with 56-bit physical addresses and a 8-way set associative cache of 64 KB where each cache line has the capacity of holding 32 words. Assume the word size is 3 and the architecture is byte-addressable. Answer the questions below: a.How many bits are needed for tag, index, word offset, and byte offs. Show your derivations and assumptions. b.What are the start and end physical addresses, in hex as discussed in class, for cache line 300? Cache line count starts from 0. c.What is the total size, in KB, of this cache? d.What is the tag value, in hex, of address 0xABCDEF98765432?
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful, do not copy and paste off chatgpt
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful
Suppose we have a byte-addressable memory of 20 bytes, built using 4 modules. Draw diagrams showing the distribution of addresses within each module, if we are using (a) highorder interleaving, and (b) low-order interleaving.
A common bus in a computer connects 16 source registers (each register is 32 bits) and one memory unit with word size of 32 bits also. If the bus is designed using multiplexers, answer the following: • What is the minimum number of multiplexers required? What is the minimum number of select lines each multiplexer has? If the bus is designed with three-state buffers and decoders, answer the following: • What is the minimum number of three-state buffers required? • What is the minimum number of decoders required? • What is the minimum size of each decode
A 16-bit address bus is carrying the address 4567H and is partially decoded with lines A15 and A13 being unused. Which one of these addresses would access a different hardware location: (a) E567H. (b) 4567H. (c) 6567H. (d) 8567H.
Suppose there is an architecture made up of 8 bit registers with 3 bit exponent. Considering this, answer the following questions. If the binary normalized form of 9E is \(-X * 2^), then what is the value of X? Write all the digits after the binary point. For the previous question, what is the value of Y? What is the binary normalized form of 7D? Sample answer: 1.0110+2^1. Use the ^ symbol for exponent. When you write the * symbol it will appear as · symbol. Write all the digits after the binary point Write the final answer in binary normalized form after performing 9E + 7D using IEEE floating-point representation. Sample answer: 1.01101000+2^1. Use the ^ symbol for exponent. When you write the symbol it will appear as · symbol. Write all the digits after the binary point Write the final answer in decimal (upto two digits after the decimal without rounding) after performing 9E * 7D using IEEE floating-point representation. Sample answer: -7.24
Suppose we have a byte-addressable computer using 2-way set associative mapping with 16-bit main memory addresses and 32 blocks of cache. If each block contains 8 bytes, determine the size of the offset field, and show your work.
Suppose we have a 16KB byte-addressable memory that is 16-way low-order interleaved. What is the size of the memory address module offset field? Explain why.
If each interval shown in Figure 7.11 is 50ns, how long would it take to transfer 10 bytes of data? Devise a bus protocol, using as many control lines as you need, that would reduce the time required for this transfer to take place. What happens if the address lines are eliminated and the data bus is used for addressing instead? (Hint: An additional control line may be needed.)
Let's pretend for a moment that we have a byte-addressable computer with 16-bit main memory addresses and 32-bit cache memory blocks, and that it employs two-way set associative mapping. Knowing that each block has eight bytes, please calculate the size of the offset field and provide evidence of your calculations.