What is the shear stress developed on the UPPER spring (in MPa)? What is the shear stress developed on the LOWER spring (in MPa)? What will the total elongation of the spring (in mm)? indicate the free body diagram

Q: Q2: A fiberglass composite consists of a matrix of vinyl ester and reinforcing fibers of E-glass is…

A:

Q: Given data: Maximum shear stress-50 MPa Maximum principal stress=80 MPa Find minimum principal…

A:

Q: What is the ratio of shear modulus to the modulus of Elasticity if Poission's ratio is 0.25

A: Given:Poission's ratio, ϑ=0.25

Q: The axial stress on the cross-section of the aluminum rod between A and C is ___ ksi. b). The…

A:

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

A:

Q: What is the true stress?

A: Need to find True stress.

Q: Compute the deformation (change in length) of bronze (B) and steel (S) in the given diagram below,…

A:

Q: Al m-piece of copper wire (diameter = 4.05 mm) is used to hang a large display item from the ceiling…

A: Given Data⇒d=4.05 mmm=7 kgE=1011Nm2we need to determine how much this wire will stretchε

Q: A nylon string has a diameter of 2 mm, pulled by a force of 100 N. Determine the stress.

A:

Q: A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly…

A: Stress is the ratio of force to the area of the material. It is denoted by the σ & measured in…

Q: If the shear stress in a material is 20 MPa and the corresponding shear strain is 0.0005, calculate…

A:

Q: At a point on a component, the stress has been calculated. The direct stress in the x direction is…

A:

Q: A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is…

A:

Q: Hooke's law describes the stress-strain relationship of the material in the

A: Given:- Hooke's law To find:- Relationship of Hooke's law

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

A:

Q: stress /Mpa 3. stain ool o:2 Q/ The figure below represents the stress-strain curve for four…

A:

Q: The formula for Critically Resolved Shear Stress is

A:

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and…

A: Thickness, t= 12 mm Width, w= 110 mm Internal diameter of the tire, d= 800 mm Wheel diameter, D=…

Q: Compare between the theoretical and practical stress strain diagram.

A:

Q: d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3

A:

Q: The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in…

A:

Q: A cast iron rod of diameter 18 mm and length of 240 mm is subjected to a tensile load of 100 kN, and…

A: As per the given data in question, the correct option is not available in options. Please find the…

Q: 1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1.…

A: The pin will be under single shear as it is joining only two components. The value of stress…

Q: Write the relation between modulus of elasticity and bulk modulus.

A: Modulus of Elasticity:- Young's Modulus is defined as the slope of stress-strain curve under direct…

Q: A helical spring having squared and ground ends has a total of 20 coils and its material has modulus…

A:

Q: must give units) a) Yield strength,Tensile/Ultimate strength,Modulus of

A: Given data Dia of specimen = 12.5 mm Gauge length = 50 mm Poisson's ratio = .33 Required Yield…

Q: What is the tensile strength of the bar if the yield stress is equal to 275MPa?

A:

Q: A material has a yield stress of 250 MPa. What tensile forces will be needed to cause yielding if…

A: A=200mm2 Stress=250MPa

Q: Where does the absolute maximum shear stress in an element of material occur?

A: Let's assume, σx and σy are the normal stresses applied to the material in x and y-direction. To…

Q: 1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1.…

A:

Q: A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N.…

A: Given data: flexural stress = 564 Pa W=1m F=10N t =2L

Q: STRESS- $TRAIN DIACRAM FOR BRAS 2 MM - SQUARE 20 CM X 24 CM 40 S A

A:

Q: What is the difference between direct and shear stress

A: Direct Stresses are tensile or compressive stresses that operate in a plane that is normal to…

Q: The shaft of a mechanical device is designed to transmit the torque T = 100 N. m. The shaft could be…

A:

Q: In a tensile test is the maximum stress that developed in a material. Select one: O a. Elastic limit…

A: Consider a stress-strain curve as shown below,

Q: Part A The plastic block is subjected to an axial compressive force of F = 500 N. (Figure 1) The…

A: The shear and normal stress along section a-a is to be calculated.   The area of block along a-a is…

Q: A new high stiffness plastic material has a length of 19.7 inches and a thickness of 3 mm and is…

A: Given data:- Force F=10000N L=19.7 in, converting into mm we get L=500.38 mm Lfinal=19.88 in,…

Q: What is the area under the stress-strain curve equivalent to? What does the area under the elastic…

A: Area under stress - strain curve is equivalent to strain energy per unit volume.

Q: Which of the followings can be found out by calculating the area only under the linear portion…

A: Option a is correct.

Q: At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2…

A:

Q: A liquid compressed in a container has a volume of 1.3 L at pressure of 1 MPa and a volume of 0.990…

A: Given data,  P1= 1 MPa  P2= 3 MPa  V1= 1.3 L  V2= 0.99 L

Q: How is the maximum shear stress determined with the torsion formula?

A: The formulae to calculate the shear stress from the Torsion formulae is as follows:

Q: a short hollow cylindrical steel compression member is required to support an axial load of 180 kN.…

A:

Q: A1 Mg container hangs from a 15 mm diameter steel cable. What is the stress in the cable?

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.