Which of following is wrong concerning the extensometer used in a tension or compression test? a. The extensometer measures directly the normal strain in the specimen b. The normal strain in the specimen can be calculated after measuring the elongation with the extensometer C. All of the answers d. The extensometer does not measure the normal stress in the specimen

Which of following is wrong concerning the extensometer used in a tension or compression test? a. The extensometer measures directly the normal strain in the specimen b. The normal strain in the specimen can be calculated after measuring the elongation with the extensometer C. All of the answers d. The extensometer does not measure the normal stress in the specimen

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

Q4) The dumbell shaped specimen is made from steel rod and is cylindrical in shape, knowing that its value for elasticity is 29000 ksi, Analyze the load which produces deflection of 0.005 inches in the specimen (b) indiviual strain at each portion in it 8 in L= 6 in L= 2 in D = 2 in D= 1.5 in D = 2 in L = 2 in
I am still confused with the sign convention we were told that in rock mechanic the sigma y in compression is positive and in tensile is negative
The thin square plate shown is uniformly deformed such that E - +1425 µE, E, - -668 uE, and ygy - +1125 prad. Determine the normal strain &, in the plate. 60 mm O -255 uE O -233 uE O -202 uE Ο -220 με O -184 uE
A steel wire with a diameter of d = 1/16” is bent around a cylindrical drum with a radius ofR = 36”.(a) Determine the maximum normal strain in the wire.(b) What is the minimum acceptable radius of the drum if the maximum normal strain mustremain below yield? Consider an elastic modulus of 30000 ksi and yield stress of 100ksi.(c) If R = 36”, what is the maximum acceptable diameter of the wire if the maximum normalstrain must remain below yield?
Q.3. (30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
In the marine crane link CD is has a uniform cross section of 50 x 150 mm and a modulus of 200 GPa. Determine the axial stress and change in length of link CD. Reference: Beer, et.al., 7th Edition Mechanics of Materials 35 m 15 m C D -15 m A -25 m. B 3 m 80 Mg
A tapered cantilever beam AB having rectangular cross sections is subjected to a concentrated load P = 46 lb and a couple Mo = 790 lb - in. acting at the free end [see the figure part (a)). The width b of the beam is constant and equal to 1.0 in., but the height varies linearly from ha = 2.0 in. at the loaded end to hp = 3.0 in. at the support. Use L = 20 in. Мо В hg (a) 3P qo = T Мо (b) ЗР 90 =7 \ Mo.
Determine the normal strain EAB in wire AB.
Define the below ? Lateral strain is considered – Skempton–Bjerrum method
The state of stress at a point in a structural member may be represented by a two-dimensional stress system in which o, =100 N/mm², o,=-80 N/mm² and 7,, =45 N/mm². Determine the direct stress on a plane inclined at 60° to the positive direction of o, and also the principal stresses. Calculate also the inclination of the principal planes to the plane on which o, acts. Verify your answcrs by a graphical method. Ans. 6,= 16 N/mm², o1 =110.6 N/mm², ơn=-90.6 N/mm², 0= –13.3° and –103.3°. !!
In terms of oxx , O yy and the material properties having a plane strain state; write the expression of the o zz Assuming there is no z-shear strain?
On the cross-section of a steel beam under bending, which one of the following statements is correct? (a) At the point where the maximum normal stress occurs, shear stress is always zero, while at the point where the maximum shear stress occurs, normal stress is not necessarily zero. (b) At the point where the maximum normal stress occurs, shear stress is not zero, while at the point where the maximum shear stress occurs, normal stress is always zero. (c) At the point where the maximum normal stress occurs, shear stress is always zero, and at the point where the maximum shear stress occurs, normal stress is also zero. (d) At the point where the maximum normal stress occurs, shear stress is not zero, and at the point where the maximum shear stress occurs, normal stress is also not zero.