Which of the following operations that can be done in one instruction on X86-64 can NOT be done in one instruction on Y86-64? Select all that apply • accessing a memory location computed by adding a register value and a constant offset • accessing a memory location computed by adding a register value and another register value adding a constant value to a register • multiplying a register value by another register value storing an 8-byte value in memory

Which of the following operations that can be done in one instruction on X86-64 can NOT be done in one instruction on Y86-64? Select all that apply • accessing a memory location computed by adding a register value and a constant offset • accessing a memory location computed by adding a register value and another register value adding a constant value to a register • multiplying a register value by another register value storing an 8-byte value in memory

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter10: Pointers

Section10.1: Addresses And Pointers

Problem 12E

See similar textbooks

Similar questions

A(n) __________ is a storage location implemented in the CPU.
_____ is a CPU design technique in which instruction execution is divided into multiple stages and different instructions can execute in different stages simultaneously.
A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
6. Update memory values for the following code. Keep track of the loop counter (R16) and index register values as you go through the loop. LDI R16,3 R15, Y+ -Z, R15 LOOP: LD ST DEC R16 BRNE LOOP STS 0x0200, R28 CPU Register R28 (YLB) R29 (YB) R30 (ZUB) R31 (ZHB) Value OxFC 0x01 0x04 0x02 Data Memory Value 0x21 0x02 0x11 0x03 Address 0x01FC 0x01FD 0x01FE Ox01FF Ox0200 0x0201 Ox0202 Ox0203
What is the addressing mode of the following no-operand instruction ? LAHF Hint: You need to check source and destination operands to determine the addressing mode category correctly. Select one: O Immediate addressing mode O Memory Based addressing mode Memory indirect addressing mode O Memory direct addressing mode O Memory Indexed addressing mode O Register addressing mode O Memory Based-Indexed addressing mode
Assume a CPU with a fixed 32-bit instruction length has the following instruction format:opcode mode [operand1] [operand2] [operand3]The mode encodes the number of operands and each operand’s mode. For instance, one mode indicates three registers, another indicates two registers and an immediate datum, another indicates a main memory reference, etc. Assume there are 94 instructions and 22 modes. Answer the following.a. One mode indicates three registers. How many registers can be referenced in this mode?b. One mode indicates two registers and an immediate datum in two’s complement. Assuming there are 32 registers, what is the largest immediate datum that can be referenced?c. One mode has a destination register and a source memory address (an unsignednumber). Assuming 16 registers, what is the largest memory reference available?d. One mode has two memory addresses, both using base displacement. In both, the basesare stored in index registers and the displacements are specified in the…
Please in assembly to 8086 processor and registers is 16 bit please write an assembly code to fill the memory with the multiple of tens as following:o The first row of memory multiple of A (10 in decimal)oand the second row multiples of 14 (20 in decimal) and so on till 46(100 in decimal)********* . (Note that the length of each row is 16 byte)After executing the code display the content of the memory using:For each question usef range to fill the buffer by your name. for me my name needs 12letter so i use the range from 400 to 40C
Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
38. Implement the following expression in assembly language, using 32-bit integers (you may modify any registers you wish): eax = -dword1 + (edx - ecx) + 1 You can use this data definition for testing your code: dword1 DWORD 10h 39. se the following data declarations to write an assembly language loop that copies the string from source to target. Use indexed addressing with EDI, and use the LOOP instruction source BYTE "String to be copied",0 target BYTE SIZEOF source DUP(0),0
13. What is the addressing mode used with the second operand in the following instruction: ADD AH, [0300]? M Stack Immediate Register indirect Direct Register Indirect
In lab this week you wrote code that simulates a simple computer; that code could be turned into a circuit. Assume that we have set up the following: • an 8-bit pc register, with 8-bit input pc_in and 8-bit output pc_out. • memory returns the instruction on the 8-bit output code_byte. Your code used a get_bits function we provided to retrieve a 2-bit part of the instruction (code_byte) as the index into the register file for register A. In a physical chip, the simplest correct form of the 2-bit extraction would be to: A. Connect 2 of the 8 wires that make up the code_byte to the register file as needed (no gates) B. A right-shift circuit to move the 2 bits for A to the least significant bits and use those two wires C. A mux with 8 bits of the code_byte as inputs and the 2 bits we want as the selector D. An even larger circuit than the ones above
Q5.Write a multiplication an Intel 8085 assembly program to multiply 2 numbers. The numbers are stored in memory locations 3000H & 3001H. Store the result in memory locations 3002H & 3003H. Show your flow chart and the assembly code. Q6. Answer True or False for the followings: a) Machine code is the assembly code b) Data field is 16 bit while address field is 8 bit c) Trainerkitcanbeused for implementing assembly code d) ADo bus can be used for addressing and datatransfer e) WR and RD pins are on the same pin