Write structured pseudocode that gives instructions to have the user enter 10 numbers, but after each number is entered, the sum of the numbers entered up to that point should be displayed. Then after the last number is entered and the last sum is displayed, the average of the 10 numbers should be displayed.

Write structured pseudocode that gives instructions to have the user enter 10 numbers, but after each number is entered, the sum of the numbers entered up to that point should be displayed. Then after the last number is entered and the last sum is displayed, the average of the 10 numbers should be displayed.

Programming Logic & Design Comprehensive

9th Edition

ISBN:9781337669405

Author:FARRELL

Publisher:FARRELL

Chapter5: Looping

Section: Chapter Questions

Problem 2GZ

See similar textbooks

Similar questions

Write a Little Man Computer program that accepts five random numbers from the user and displays them in ascending order. Attached is the Little Man Mnemonic Instruction Codes:
Write a program in MIP assembly language in the MARS Simulator A )Display a prompt to the user: “Enter a number: “ B) Wait for the user to enter an integer. C) If the number entered is zero Print “The sum is: “ followed by the sum of all of the integers entered. Print “The number of integers entered was: “ followed by the number. D) Exit the program and Loopback to step A.
Course: Assembly Language Write an assembly program that lets the user to type some text, consisting of wordsseparated by blanks, ending with carriage return, and display the text in the same word orderas entered, but with the letters in each word reversed. For example, “this is a test” becomes“siht si a tset”. Note: code in 8086 processor
Scenario: A robot is sitting in a chair with its arms facing down. Write an algorithm, using pseudocode, to make the robot: stand up walk until it senses a wall turn around walk back to the chair sit back down in the origin starting position Finally, output the total number of steps taken. Commands: In addition to our standard pseudocode commands, you must also use the following robot control commands: sit stand step (one step forward) raise arms (parallel to floor) lower arms (pointing to floor) sense (only if arms are raised) turn (90 degrees right) Immediately after issuing a sense command, you can check if the robot is at a wall.You do this via the boolean conditions "at wall" or "not at wall".The following are examples of this: if at wallif not at wallwhile not at wall AssumptionsYou must assume the following facts: The robot's initial sitting position is directly facing the target wall. There are no obstacles between the robot and the wall. The wall is 1 or more exact steps…
Write AWT Java program that simulate the PINCODE process. The system has a default PINCODE of 6 digit numbers; the user should enter 6 digit numbers using the NUMBER PAD button. To verify the correct PINCODE the user should click the ENTER button. It will display a message box “You are authorized” if the user entered a correct PINCODE otherwise it will display a message box “You are not authorized!!!”
In python, Problem DescriptionProfessor Santos has decided to hide a secret formula for a new type of biofuel. She has, however, left a sequence of coded instructions for her assistant. Each instruction is a sequence of five digits which represents a direction to turn and the number of steps to take. The first two digits represent the direction to turn: • If their sum is odd, then the direction to turn is left.• If their sum is even and not zero, then the direction to turn is right.• If their sum is zero, then the direction to turn is the same as the previous instruction. The remaining three digits represent the number of steps to take which will always be at least 100. Your job is to decode the instructions so the assistant can use them to find the secret formula. Input SpecificationThere will be at least two lines of input. Each line except the last line will contain exactly five digits representing an instruction. The first line will not begin with 00. The last line will contain…
Take an lowercase letter as input from the user (omit error checking, so you do not have to write code for checking whether the user is inputting upper case or lower case), and display it at the next position on the next line in upper case. Please complete it with assembly language that can run on "emu8086". Sample Execution 1: a A Sample Execution 2: b B
Translate the following pseudocode for finding the minimum value from a set of inputs into a Java program.Set a Boolean variable “first” to true. While another value has been read successfully If first is true Set the minimum to the value just read Set first to false Else if the value is less than the minimum Set the minimum to the value Print the minimum
JAVA LANGUAGE Sort It Yourself by CodeChum Admin A descending order means values arranged from largest to smallest. But in your case, you're going to have to sort these integers in ascending order, which means from smallest to largest. Instructions: Input three integers. Print the integers in ascending order using your knowledge on conditional statements. Input A line containing three integers separated by a space. 6·1·3 Output A line containing three integers separated by a space. 1·3·6
Write a java program that asks a user to enter a set of positive integer values. When the user stops(think of sentinel value to stop), the program displays the maximum value entered by the user. Yourprogram should recognize if no value is entered without using counter.
Write pseudocode to describe an average mark calculator program that computes the average mark for a course. 1. The program prompts the user to enter the following information: a. Request that the user type in the course code.b. Request each student mark be entered one at a time. 2. The program executes continuously (each time prompting for the next student mark) until the user enters a negative number to signal that the marks entry is completed. Note that a negative number is not considered a mark. 3. The program then outputs the following information:a. The course code.b. The average mark for the course.c. The highest mark for the course.d. The lowest mark for the course.4. The program then restarts from (1). 5. To exit the program, the input "stop" is entered in the course code prompt.Declare your variables. *Guide me to solve this question with step-by-step solution. Thank you in advance.
Write a PEP/9 assembly language program that prints "Please enter a number", then gets a number from the user, then divides that number in half and prints it out.