Wye connected source with the voltage of 460 V. Delta connected load of R=3Ω, XL=4Ω Find: a. The actual current phasor in the delta connected load. b. Do the calculations a second way to check your answer. c. Repeat for the case where the source is delta connected and the load is wye connected. d. Do the calculations a second way to check your answer.

Wye connected source with the voltage of 460 V. Delta connected load of R=3Ω, XL=4Ω Find: a. The actual current phasor in the delta connected load. b. Do the calculations a second way to check your answer. c. Repeat for the case where the source is delta connected and the load is wye connected. d. Do the calculations a second way to check your answer.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 9RQ: What is the power factor of the circuit in Question 6?

See similar textbooks

Similar questions

I. Suppose the voltage across the resistor is ΔvR = ΔVmax= RVmax sin wtFind the current through this resistor and draw the waveforms of both current and voltageHere R is equal to 4.
I. Suppose the voltage across the resistor isΔv R = ΔV max = RV max sin wtFind the current through this resistor and draw the waveforms of both current and voltageHere R is equal to 4
. Determine the total resistance and the total current using delta to wye transformation.
A series-parallel ac circuit has two branches across the 60 Hz , 220 V power line. One branch has a 20 ohm R1 in series with a 10 ohm R2. The other branch has a 30 Mega ohm R3 in series with a 10 Mega ohm R4. Calculate the voltage across R4.
Which of the following is a Load and Resistance Design Concept? O Service load O Rn/2 O Factored load O Allowable load
6. Example sheet 1 Thunsday, 18 une 2000 15 PM 1. A series R-L circuit, R = 30 0, L = 0.025 H is supplied by 250 V. 60 Hz source. Enms a. Find the current in the circuit. b. Power and pf of the circuit.
The dc load voltage across the load of FIGURE 4 is 91.51V. Compute the value of R1. LOAD R1 R2 Vac k= 20mA 5kohms 220V, IGT= 25mA 60HZ 5.72kohms O 3.21kohms O 1.57kohms
R1 R,1 kN 5 k 8 k 5 k. E, = 10 VZ0° 4 k0 2.5 kN Figure 4 4. For Figure 4 above a. Is the network balanced? Show your work b. What is the current through the capacitor? ll
What is the power factor of the circuit in Question 6?
a. Determine all the impedance values in the Figure 1 and Figure 2. b. Find the total current flowing in Figure 1 and Figure 2. Procedures Task 1 R =120 L = 0.15H C = 100uF VR VL Vc I Vs = 100V, 50HZ
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?
1 Ia = ?? A 2.ib= ?? A 3 Vx = ?? 4 power at Rx = ?? 5 power at Rb = ??