. In an orthogonal cutting operation,uncut chip thickness t is = 0.127 mm.%3Dchip thickness t is = 0.228 mm and rakeangle a is = 10°. The shear angle is1) 20.502) 31.250fand=3casdJoonge-13) 40.25°4) 35.50

Answered: Image /qna-images/answer/0770cac4-98ae-4e24-8e38-80ddc7d90161.jpg

. In an orthogonal cutting operationn, uncut chip thickness t is = 0.127 mm chip thickness t is = 0.228 mm and rake angle a is = 10°. The shear angle is 1) 20.50 2) 31.250 fand=3cass 3)40.250 4) 35.50

. In an orthogonal cutting operationn, uncut chip thickness t is = 0.127 mm chip thickness t is = 0.228 mm and rake angle a is = 10°. The shear angle is 1) 20.50 2) 31.250 fand=3cass 3)40.250 4) 35.50

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In orthogonal cutting, the depth of cut is 0.5 mm at a cutting speed of 2 m/s. If the chip thickness…

Q: Technician is turning (lathing) a work material with shear strength of 250 MPa as shown in Fig.1.…

Q: The rpm (N) of the shaft, diameter (d) =25 mm, cutting speed (v) =50 m/min is; O 39.25 O 636.9 O…

A: Given data as per question Diameter of shaft=25 mmcutting speed =50mmincalculating speed of…

Q: In a turning operation on stainless steel, cutting speed = 150 m/min, feed = 0.25 mm/rev, and depth…

A: From the given table write the specific energy for cutting stainless steel.

Q: A shaft groove with a length of 250 mm and a depth of 12 mm is cut by a 20 mm diameter slot cutter.…

A: Given:L=250 mmh=12 mmD=20 mmd=4 mmf=25 mm/minLo=12*D

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Is the elastic modulus im portant for cutting-tool materials? Explain

Q: 21.65 The following data are available from orthogonal cut- ting experiments. In both cases depth of…

A: “Since you have posted a question with multiple sub-parts, we will solve three sub-parts for you. To…

Q: Turning is performed on a work material with shear strength of 250 MPa. The following conditions are…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Question 4. The following data are available from orthogonal cutting experiments. The depth of cut…

A: When the cutting edge is perpendicular to the machined surface, the cutting executed is termed…

Q: Q4) A face milling operation is used to machine 5 mm from top surface of a rectangular piece of…

Q: C, where V is in m/min and T is in min. In a turnin Taylor's tool life equation is given by VTn…

Q: Low carbon steel having a tensile strength of 450 MPa and a shear strength of 270 MPa is cut in a…

A: Answer: Shear plane angle, ϕ = 31.28° Shear Force, Fs = 195.21 N Cutting Force, Fc = 333.67 N and…

Q: In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness after cutting is 2 mm,…

A: The cutting operation in which the angle between the cutting edge of tool and cutting velocity is 90…

Q: In a turning operation on cast iron (150 BHN), the cutting speed is 340 ft/min, feed is 0.06 in/rev,…

A: Given data as per question Cutting speed = 340 ft/min Feed =0.06 in/rev Depth of cut =0.05…

Q: In the horizontal milling machine, plain milling is accomplished on the top surface of a rectangular…

Q: Since the cutting plane angle is 9.5°, the cutting depth is 0.4 mm, the chip thickness is 2.9 mm,…

A: 1.We know that rack angle=Cutting plane angle=9.50

Q: 22.14. A peripheral milling operation is performed on the top surface of a rectangular workpart…

A: According to the given information, the length of the workpiece is 400 mm, the width of the…

Q: n an orthogonal machining with a tool of gº orthogonal rake angle, the uncut chip thickness is 0.2…

A: Given:Orthogonal rake angle, α=9ouncut chip thickness, t=0.2 mmmaximum chip thickness, tmax=0.4…

Q: The cutting force increases with the depth of cut and decreasing rake angle. Explain why

A: Depth of Cut:- When the depth of cut increase, then the amount of material removed in a unit time…

Q: In the lathe machine, steel rod with diameter 160mm is turned under the following condition: Axial…

Q: 3 In an orthogonal machining process, the following observations were made: Rake angle of tool 10°…

A: Option a is correct.

Q: Q1:- Choose the appropriate word. (1):- The fixed cost its ----- with number of products a- Change…

A: As per question answered all the questions above

Q: In an orthogonal cutting operation, the tool has a rake angle = 35°. The chip thickness before the…

A: Given data rake angle () = 35o uncut chip thickness (t) = 0.90 mm chip thickness (tc) = 0.75 mm…

Q: Q) An engine lathe is used to turn a cylindrical work part 150 mm in diameter by 500 mm long.…

A: GIVEN: D=150mm L=500mm F=0.3mm/rev d=3mm Cutting speed, V=2.5m/s=2500X60=150000mm/min a) CUTTTING…

Q: Details pertaining to an orthogonal metal cutting process are given below Chip thickness ratio 0.4…

Q: If shear strength is 6000 kg/cm2, width of cut is 10mm, cutting speed is 30 m/min, coefficient of…

A: Given:shear strength,ζ=6000 Kg/cm2 =6000*9.8110-4ζ=588.6 MPab=10 mmVelocity of cutting,V=30…

Q: Penny's duty 1: If you know that n = 0.5 and C = 90, using Taylor's equation, find the percentage…

A: (i) To find : The percentage increase in the life of the cutting tool when the cutting speed…

Q: Which option about chief elements in metal cutting is wrong? a)Chip width is the distance between…

A: Feed of cutting is expressed in mm per revolution. And cutting speed is expressed in mm per second.

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: In an orthogonal cutting operation, the tool has a rake angle = 45°. The chip thickness before the…

A: Given DAta Chip thickness before the cut, t=0.75 mm rake angle, 45 degree Deformed chip thickness,…

Q: In an orthogonal cutting test on mild steel, the following data were obtained Cutting speed Depth of…

Q: A.) A cutting operation is performed on a piece of metal. The rake angle of the tool, α, is eight…

Q: In a dry cutting operation using a -5 degree rake angle, the measured forces were; cutting force =…

A: Consider Fc and Ft be the cutting force and feed force respectively during an machining operation…

Q: Clarify the relation of slope and rate of change?

A: The slope is the ratio of the vertical and horizontal changes between two points on a surface…

Q: Question 3. A cemented carbide tool is used to turn a part with length= 18.0 in and diameter = 3.0…

Q: 3. Draw the forces and angles involved in the cutting process and calculate shear angle (Ø),…

A: Given Data⇒ Cutting ForceFc=80 KN Resultant of forcesFr=100 KN Friction force(F)=75 KN Rake…

Q: The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6…

A: Given Data: Rake angle α=20° Depth of cut d=6 mm Feed rate f=0.25mmrev Cutting speed VC=0.6ms Chip…

Q: In an orthogonal cutting test on mild steel, the following data were obtained Cutting speed Depth of…

Q: State whether or not the following statements are true, explaining your reasons: (a) For the same…

A: a) For the same shear angle, there are two rake angles that give the same cutting ratio,…

Q: Question: Determine the optimum cutting speed for an operation on a Lathe machine using the…

A: Given:-Tc=tool change time=3 minTr=tool regrinds time= 3 minCm= Machine running cost= Rs 0.50 per…

Q: Show that, for the same shear angle, there are two rake angles that give the same cutting ratio

Q: A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by…

Q: 29- In a turning operation on brass with hardness 125 HB, the cutting speed = 200 m/min, teed = 0.25…

Q: D. = 0.250" D, = 0.125" L- 6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev;…

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

Q: D. 0.250" D, = 0.125" L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev;…

A: Cutting speed v=211 ft/minor v=211×12 =2532 in/minf=.0018 in/revD0=.250''Df=.125''L=6.250''

Q: A variety of __________ saws blades are available for rough cuts in wood, smoother cuts in wood,…

A: A Reciprocating Saw is a handheld saw commonly used for demolition and remodeling. You can use it to…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

. In an orthogonal cutting operation,
uncut chip thickness t is = 0.127 mm.
%3D
chip thickness t is = 0.228 mm and rake
angle a is = 10°. The shear angle is
1) 20.50
2) 31.250
fand=3casd
Joonge-1
3) 40.25°
4) 35.50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine to reduce the diameter to Ø 45mm. The cutting parameters are 23 m/minute, 0.3 mm/ revolution and 0.5 mm are cutting speed, feed and depth of cut respectively. Determine the following. i) Time for single pass (minutes). ii) Find number of passes required to reduce the diameter from Ø55 to Ø45mm. iii) Total time required to complete the turning operation in minutes (Tfinal).
An orthogonal cutting operation is being carried out in which to=0.2 mm, V=2m/s, a=7.5o, and the width of cut=5 mm. It is observed that tc=0.25mm, Fc=400N, and Ft=300N. Calculate the percentage of the total energy that is dissipated in friction at the tool-chip interface. A) 22% B) 50% C) 70% D)None of the above
Which one of given below is nota chip type? 31 - Aşağıdakilerden hangisi talaş türü değildir? Continuous chip with built-up edge A) yığma kenarlı sürekli talaş Discontinuous chip B) süreksiz talaş Multiple cutting edge chip çoklu kesme kenarı talaşı Serrated chip D) tırtıklı talaş Continuous chip E) sürekli talaş
A circular shape blank will be cut of 106.9 mm diameter from a strip of 3.49 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine a) The appropriate punch diameter. b) Blanking force. c)Blanking force when the blade angle is 5.69 o.
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
Consider a milling process, where a pocket with width (X) of 400mm, Length (Y) 300mm, and depth (z) of 15 mm. The cutting tool is a 12 mm diameter flat end mill with 4 cutting edges. For some reason, the tool can be radially immersed in the material at most 50% of the tool diameter. The spindle speed is selected as 2000 rpm, where the max allowable axial cutting depth is 2.5 mm. a) Calculate the number of total cutting steps, indicating which feed direction would you prefer x or y. It may be preferred to have feed rate can be along X direction Total # of cutting steps: If feed direction is along X, the total number of cutting steps is 294 b) Calculate the minimum achievable cycle time if the feed rate is 0.15 mm/rev/tooth. Approx cycle time: 98 minutes
The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6 mm Feed rate = 0.25 mm/rev Cutting speed = 0.6 m/s Chip length before cutting = 29.4 mm Vertical cutting force = 1050 N Horizontal cutting force = 630 N Chip length after cutting = 12.9 mm Using Merchant's analysis, calculate (a) Magnitude of resultant force, (b) shear plane angle, (c) friction force and friction angle, and (d) various energies consumed.
A 5 m wide by 12 m long and 20 mm thick steel plate is to be cut into 8 equal parts lengthwise. If the cutting rate is 3.75 mm per stroke using a hacksaw with a speed of 200 rpm, how long will it take the job in hours. There is only one cut stroke per revolution. D O 1.78 O7.18 O 1.87
2) In an orthogonal cutting operation, the cutting tool has a rake angle = 20°. The chip thickness before the cut = 0.25 mm. If the cutting force and thrust force are measured during an orthogonal cutting operation with values, Fc = 1450 N and Ft = 1990 N. The width of the orthogonal cutting operation w = 2.5 mm. the friction angle B is = 79.91° Determine: The Shear Angle The Shear Strain The Shear Strength of the material The Force of Friction
Which option about chief elements in metal cutting is wrong? a)Chip width is the distance between D and d along the cutting surface b)The cutting speed is expressed in mm per revolution c)Feed s is the tool distance moved along the axis per revolution of the work d)Depth of cut t is the distance between D and d
Tuming tests were performed using a coated carbide tool on steel workpiece at feed of 0.30 mm/rev and the depth of cut 4.0 mm. The tests have resulted in 20-min tool life for a cutting speedv 165 m/min and a 60-min tl mie ie a speed v = a) The n and C values in the Taylor tool life equation b) The cubic cm of steel removed in each case 96 m/min. Determine:
In orthogonal cutting, the depth of cut is 0.5 mm at a cutting speed of 2 m/s. If the chip thickness is 0.75 mm, the chip velocity is а. 1.2 b. 1.67 1.33 d. 1.44 оо